Publicité
Les langues disponibles
Les langues disponibles
English
Inserting an Accessory (Fig. C)
1. Hold the screwdriver upright as shown in Figure C and pull
down on the quick release collar
2. Insert a hex shank accessory into the holder.
3. Release the quick release collar.
nOTE: If bit does not fit into spindle, rotate the bit and
reinsert it.
Removing an Accessory (Fig. C)
1. Hold the screwdriver upright as shown in Figure C and pull
down on the quick release collar
2. Pull accessory straight out.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off before making any adjustments
or removing/installing attachments or accessories.
An accidental start-up can cause injury.
Proper Hand Position (Fig. A, D, E)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main handle
Hold tool firmly to control its twisting action.
Angling the Screwdriver (Fig. A, E)
WARNING: To avoid being pinched, hold the screwdriver
as shown in Figure E when changing positions.
To convert the tool to an angled screwdriver, push in on the
release button
6
and rotate the top portion of the tool until it
locks into one of the remaining two positions.
Torque Control (Fig. F)
The torque adjustment collar
a drill bit icon. There are 22 clutch settings in all. Each click in a
clockwise direction means an increase in the torque produced.
To set the torque align the desired setting with the arrow on the
tool housing. The higher the number on the collar, the higher
the
torque.
If
you do not know the appropriate setting to use when
tightening a screw, begin at the lowest torque setting. If the
clutch ratchets before the desired result is achieved, increase the
collar setting and continue tightening the screw. Repeat until
you reach the correct setting.
Two Speed Operation (Fig. A)
The dual range feature of your screwdriver allows you to shift
gears for greater versatility.
8
.
4
4
.
2
is marked with numbers and
To select low speed, (high torque setting), turn tool off and
permit to stop. Push the slide switch
the tool to the left. Use low speed for screwdriving operations.
To select the high speed, (low torque setting), turn tool off and
permit to stop. Slide gear shifter fully to the right.
LED Light (Fig. A)
To turn the light
3
underside of the screwdriver toward the front of the tool.
MAINTENANCE
Your D
WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
WARNING: To reduce the risk of serious personal
injury, turn tool off before making any adjustments
or removing/installing attachments or accessories.
An accidental start-up can cause injury.
The charger and battery pack are not serviceable.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
.
9
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
Optional Accessories
WARNING: Since accessories, other than those offered
by D
WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Consult your dealer for further information on the
appropriate accessories.
Protecting the Environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
4
located on the top of
on, push the slide switch located on the
WALT recommended
e
Publicité
