Makita RP0900 Manuel D'instructions page 9

Drill point double flush trimming bit (Fig. 23)
D A L 1
8 8 80
6 6 70
Corner rounding bit (Fig. 24)
D A 1 A 2
6 25 9
6 20 8
Chamfering bit (Fig. 25)
D A L 1
6 23 46
6 20 50
6 20 49
Cove beading bit (Fig. 26)
D A
6 20
6 25
Ball bearing flush trimming bit (Fig. 27)
D A
6
10
1/4"
Ball bearing corner rounding bit (Fig. 28)
D A 1 A 2
6 15 8
6
21 8
1/4"
Ball bearing chamfering bit (Fig. 29)
D A 1 A 2
6
26 8
1/4"
6 20 8
Ball bearing beading bit (Fig. 30)
D A 1 A 2
6 20 12
6 26 12
L 2 L 3
55 20
40 12
L 1 L 2 L 3
48 13 5
45 10 4
L 2 L 3
11 6
13 5
14 2
L 1 L 2
43 8
48 13
L 1
50
L 1 L 2 L 3
37 7 3.5
40 10 3.5
L 1 L 2
42 12
41 11
A 3 L 1 L 2 L 3
8 40 10 5.5
8 42 12 4.5
Ball bearing cove beading bit (Fig. 31)
mm
L 4 D A 1
25 6 20
14 6 26
Ball bearing roman ogee bit (Fig. 32)
mm
R D A 1
8 6
4 6
Noise
mm The typical A-weighted noise level determined according
to EN60745:
θ
Sound pressure level (L
30°
Sound power level (L
Uncertainty (K): 3 dB (A)
45°
60°
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745:
mm
Work mode: cuttig grooves in MDF
Vibration emission (a
R
Uncertainty (K): 1.5 m/s
4
• The declared vibration emission value has been
8
measured in accordance with the standard test method
and may be used for comparing one tool with another.
mm • The declared vibration emission value may also be
used in a preliminary assessment of exposure.
L 2
WARNING:
• The vibration emission during actual use of the power
20
tool can differ from the declared emission value
depending on the ways in which the tool is used.
• Be sure to identify safety measures to protect the
mm
operator that are based on an estimation of exposure in
the actual conditions of use (taking account of all parts
R
of the operating cycle such as the times when the tool
3
is switched off and when it is running idle in addition to
the trigger time).
6
For European countries only
EC Declaration of Conformity
We Makita Corporation as the responsible
manufacturer declare that the following Makita
mm
machine(s):
θ
Designation of Machine:
Router
45°
Model No./ Type: RP0900
are of series production and
60°
Conforms to the following European Directives:
98/37/EC until 28th December 2009 and then with
2006/42/EC from 29th December 2009
mm
And are manufactured in accordance with the following
standards or standardised documents:
R
EN60745
4
7
A 2 A 3 A 4
18 12 8
22 12 8
A 2 L 1 L 2
20 8 40 10
26 8 42 12
): 89 dB (A)
pA
): 100 dB (A)
WA
Wear ear protection.
): 4.0 m/s
h
2
mm
L 1 L 2 L 3 R
40 10 5.5 3
42 12 5 5
mm
L 3 R1 R2
4.5 2.5 4.5
4.5 3 6
ENG102-3
ENG223-2
2
ENG901-1
ENH101-13
9