Nordcap MORETTI S Serie Mode D'emploi page 24

START) keys.
WARNING!
The sound alarm serves to signal that the
equipment is about to start up and therefore, anyone within its radius
of activity for any reason must move to a safe distance or disconnect
the equipment from the power supply; the above function and
relevant risk must be made known to all those who might be in the
vicinity of the equipment for the purpose of safeguarding them
against accidents or injury.
Once the oven has started up (or has switched off) at the set time, the
"Timer" function remains operational. Therefore, if no changes are made,
one week later at the same time, the oven will start up (or shut down)
again.
NOTE:
If the operator forces an oven start-up when the timer is
switched on before the set time, then the oven will start up normally
and at the start-up time set for the timer, everything will proceed as
usual (the oven is already on and therefore no buzzer will sound).
The same thing happens if the oven is already off at the time set for
shut down.
NOTE:
If there is a power outage while the timer is engaged,
(Blackout), no important parameter will be changed and This is as
long as the power returns before the set switch on time.
NOTE:
The control unit, powered by furnace in STOP, is
equipped with an internal timer after which automatically turns off
the display. Pressing any button wakes up the controller. With
genenerale switch in position "1" and the display is off make sure
that the unit does not enter into this state before turning off the
circuit breaker. Turn on the unit by pressing any key, then proceed
as in paragraph 3.9.
3.5.5 SETTING THE TIME/DATE
The following items can be selected on the display by scrolling the list
with the "SELECTION" keys:
- "Settings": to set the time and date, use the "SELECTION" keys to
move into the field to be changed. Use the "+" and" keys to
increase/reduce the selected field.
- "Time Zone": proceed with the time zone setting in GMT format (e.g.
GMT 00 London, GMT +1 Rome, etc.).
Press "OK" to confirm the change. Press "RETURN" to go back to the
previous screen without confirming the changes.
The time format is HH:MM. The date format is given as DD/MM/YY.
3.5.6 LANGUAGE SETTINGS
To set the language, scroll through the list with the "SELECTION" keys
as far as the required item and press "OK" to confirm. Press
"RETURN" to go back to the previous screen without confirming the
changes.
3.5.7 °C/°F SETTING
The oven can be set to use/view temperatures in centigrade (°C) or
Fahrenheit (°F). The current setting is shown on the main screen to the
right of the measured temperature with the relevant symbol.
To change the current settings, scroll through the list with the
"SELECTION" keys to find the required item and press "OK" to
confirm. Press "RETURN" to go back to the previous screen without
confirming the changes.
3.5.8 SERVICE
This menu contains information about the oven which will be needed
when requesting Assistance.
Scroll through the list on the display using the "SELECTION" keys to
select the following items.
- "Info": shows information about Service, about the version of the
software installed and the configuration of the oven.
- "Software upgrade": Starts the software upgrade process
WARNING!
Procedure reserved to trained personnel
authorised by the Manufacturer. The operation may compromise
the correct operation of the appliance.
- "Reset": this starts the partial reset to factory settings (any other
Programs present will be deleted)
ATTENTION!
This procedure is reserved only to persons
trained and authorised by the Manufacturer. This operation may
affect the correct operation of the appliance.
- "Factory default": this starts the general default procedure for
factory settings (any Programs stored will be maintained in the
memory)
WARNING!
Procedure reserved to trained personnel
authorised by the Manufacturer. The operation may compromise
the correct operation of the appliance.
- "Align": starts the vertical alignment process for the graphic.
Use the "SELECTION" keys to move the corresponding graphic.
- "Alarms": shows any ongoing errors. The "SELECTION UP" key
scrolls through the list of alarms present. The appliance status, in
case there are pending alarms, it shown on the status bar with the
corresponding status icon (fig.17 item N).
- "Logfile": procedure for saving baking data, reserved to the
Assistance centre.
- "Delta Power": function that allows the power at the oven opening
to be increased/reduced while maintaining the user's power settings.
This function serves to balance out the oven settings between the
front and back. Use the specific keys to make this correction
(expressed in percentages) to the ceiling and bedplate of the oven:
positive values increase the power, while negative values will
reduce it. The corrections set will be applied at the power
percentages used in SMART BAKING mode.
- "Sensitivity": a function that makes it possible to adjust oven
sensitivity to changes in temperature, electronically. Three settings
are available (from least to most sensitive): "Low", "Default"
(factory settings) and "High".
- "Slit Booster": a function that makes it possible to set in which zone
the Power Booster function needs to provide additional power. The
following settings are available: "Ceiling & Bedplate" (factory
default), "Ceiling only" and "Bedplate only". Select the required
setting according to the type of product being baked.
- "Energy Consumption Estimate": a summary of the estimated
energy consumption:
o
o
o
NOTE:
The meters provide an estimate of the energy
consumption and refer to nominal power values. Actual
consumption depends on the power utility supply, so it may differ
from the estimated consumption!
- "Wi-Fi": use this menu to connect the oven to the local WiFi
network:
•
Enable / Disable: to scan the available networks and connect/
disconnect
•
Info: summary screen of network parameters (if connected)
•
Search for other WiFi: to switch to another WiFi network (if
connected)
Press "OK" to confirm the selected item. and follow the instructions on
the screen. Press "RETURN" to return to the previous screen without
confirming the changes.
3.5.9 MULTITIMER
The "Multitimer" display serves to control 6 independent "Baking
timers". Enabling this function opens a dedicated screen that associates
a timer control to each neutral key (fig.22A). For operation and timer
control, see"BAKING TIMER" in 3.2.2. Press the "TIMER 1" or
"TIMER 2" keys (fig. 15 part.5) to pass to the baking parameter screen
and set the temperature/power. Press one of the two keys again to go
back to the timer control screen.
If an operating baking timer should expire, the timer screen will open to
allow the user to view the expired timer, which is indicated by a flashing
light.
To edit the settings for the 6 baking timers, press the "MENU" key,
select the BAKING TIMER with the "SELECT" key and then press
"OK" to access the submenu in order to select "Settings" and change the
set times (fig.19a). In MULTITIMER mode the settings for the 6 timers
are made on three separate screens (two timers for each screen).
3.5.10 METRONOME
The "Metronome" display consists of 6 synchronised timers that are
represented in the display by 6 empty bars. These bars get filled as time
elapses and become coloured when the preset times is about to expire. A
beeping sounds is triggered when each preset time expires. Setting all
timers follows the same procedure used for TIMER 1 Based on this
setting, an algorithm automatically calculates the offset between one
timer and the next so that during execution, the waiting time between the
expiration of a timer and the next is similar.
This function allows the user to have:
- a visual correspondence between the display and the baking areas
- a tool that helps to synchronize the work of placing into the oven and
taking out of the oven, very useful in repetitive productions (e.g. pre-
cooked bases, etc.)
UK/9
Instant power, Mean power, Maximum power
(press the corresponding button to scroll through
the various parameters)
Partial energy meter (press the Trash Bin button
to reset the partial energy meter)
Total energy meter