EINHELL RT-HP 130 Mode D'emploi page 12

Anleitung_RT_HP_130_SPK1:_
GB
and + 60°C.
b Do not cover or modify the lance or the spray
nozzles in any way.
b The high-pressure cleaner is designed to be
used with cold or lukewarm water (max. 50°C);
higher temperatures can damage the pump.
b Do not use water that is dirty, gritty or contains
any chemical products, as these could impair
operation and shorten the life of the equipment.
5.2 Assembly
5.2.1 Assembling the equipment
Assemble the high-pressure cleaner as shown in
Figure 2-8.
5.2.2 Water inlet connector (Fig. 1/13)
The connection for the water inlet (13) is equipped
with a connector for standard hose coupling systems.
Attach the hose coupling on the supply hose (min. Ø
1/2") to the connector for the water inlet (13).
An anti-vacuum device must be installed between
the water tap and the high-pressure cleaner! Ask
your local plumber about this.
5.2.3 Connecting the high-pressure hose
(Fig. 9-11/18)
Remove the transport brace as shown in Figure 9
from the connection for the high-pressure hose (9).
Connect the high-pressure hose (18) to the
connection on the high-pressure cleaner (9) and on
the spray gun (14).
5.2.4 Fitting the gun attachments
The normal lance, the lance with rotating nozzle or
the rotating washing brush can be attached prior to
using the high-pressure cleaner (Fig. 12).
Lance point / wide cone (16)
The shape of the water jet can be changed from
concentrated to flat jet by turning the nozzle (Fig.
15).
Lance with rotating nozzle (17)
To remove particularly stubborn dirt, use the lance
with rotating nozzle (17).
Rotating washing brush (15)
The rotating washing brush (15) is intended for (low
pressure) cleaning with cleaning agent.
12
18.02.2008 16:02 Uhr Seite 12
5.2.5 Electrical connections (Fig. 1)
b Before you connect the appliance to the mains
supply make sure that the data on the rating
plate are identical to the mains data.
b If you use any extension cables, make sure that
they are suitable for outdoor use and have large
enough wires:
1 – 10 m: 1.5 mm
10 – 30 m: 2.5 mm
b Plug the mains plug (8) on the power cable (6)
into the mains socket outlet.
6. Operation
The equipment consists of an assembly with a pump,
which is encased in a shock absorbing housing. The
equipment comes with a lance and a non-slip gun
(for an optimal working position), whose shape and
configuration comply with the applicable regulations.
6.1 Using for the first time:
Once you have completely assembled the high-
pressure cleaner and connected all connections,
proceed as follows:
Open the water inlet. Press safety pin "a" (Fig. 12) on
the spray gun and pull back trigger lever "b" (Fig. 12)
in order to bleed the trapped air out of the device.
Turn on the device by switching the ON/OFF switch
(Fig. 1/12) to "I".
To temporarily turn off, release the trigger lever (b),
at which point the device goes to standby. As soon
as you press the trigger lever again (b), the high-
pressure cleaner restarts.
To completely turn off the high-pressure cleaner,
switch the ON/OFF switch (Fig. 1/12) to "0".
6.2 Using cleaning agent (Fig. 1):
Fill the integrated cleaning agent tank (4) with
suitable cleaning agent. By pulling back the nozzle
head on the lance (16) the unit will change to low-
pressure operation and the cleaning agent will be
added automatically. The washing brush (15) only
works with low pressure and with automatic
detergent mixing.
6.3 Holder for the gun/accessories (Fig. 13-14)
The gun and accessories can be kept in the provided
holder (2; 10) in order to save space when not in
use.
2
2