monzana DBHC002 Manuel page 13

Adjusting the pressure plate
Figure 6
The pressure plate is set at the factory. Adjust-
ment is only required when it is worn or, if need
be, after clearing blockages. Wear can be seen by
the fact that material is only squashed and
remains attached in a chain-like manner.
– Switch the directional switch (5) to the
forwards position, and switch on the product.
– Turn the adjustment screw (8) clockwise until
you can hear minor grinding noises.
– The pressure plate has been adjusted.
CAUTION! Device
damage! Adjusting the pres-
sure plate too far will cause
unnecessary wear.
Replacing the pressure plate
DANGER! Risk of injury!
Switch the product off and pull
the power plug before replac-
ing the pressure plate. Wait
until all moving parts have
come to a standstill and the
product has cooled down.
Figure 7
– Undo the four screws (9) and remove the
protec-tive plate (10).
– Replace the pressure plate (11).
– Replace the protective plate (10) back on the
product and secure using screws (9).
Cleaning and maintenance
DANGER! Risk of injury!
Switch off the product and
disconnect from power before
all cleaning and maintenance
work. Wait until all moving
parts have come to a standstill
and the product has cooled
down.
Cleaning the product
Careful handling and regular cleaning ensure that
the product stays fully functional and efficient
over a long period of time.
•Remove loose dirt with a brush.
•Wipe the tool with a damp cloth.
•Never spray the product with water or expose
to water.
•Never use cleaning fluids or solvents for
cleaning. This may irreversibly damage the
product. The plastic parts may be attacked by the
chem-icals.
•Keep ventilation slots clean and free of dust.
Transportation
•Secure the product to prevent shifting.
•When dispatching, try to use the original
packaging, if possible.
Troubleshooting
DANGER! Risk of injury!
Unprofessional repairs may
mean that your product will no
longer operate safely. This
endangers you and your envi-
ronment.
In many cases, small defects can lead to a
malfunction. You will usually be able to deal with
these yourself. Please consult the following table
before contacting the service department. This
may save you a lot of effort and quite often
money.
www.Deuba24online.de
Error/Fault
The motor does not work.
Material to be cut is not
pulled in.
Chipped material is still
attached in a chain-like
manner.
Please contact service department directly if you
cannot eliminate the error by yourself. Please
remember that repairs carried out by non-profes-
sionals will invalidate your warranty claim and
may cause additional costs.
Technical data
Model
Nominal voltage
Capacity
Protection class
Protection rating
Idle revolutions
Maximum cutting
diameter
Guaranteed sound
power level.
Sound pressure level at
the user's place.
Measured sound power
level
Weight
25 www.Deu b a2 4o n line .de
24
Cause Remedy
No power supply? Check the cable, plug, and
the fuse.
Has the motor protection Remove all chipping material
mechanism been triggered? and press the reverse button.
Blade drum is in reverse? Switch it off, switch the
directional switch to the
forwards posi-tion, switch on.
Material is too soft? Use wood to push through,
or dry branches and twigs.
Blade drum is blocked? Eliminate the blockage.
Pressure plate is not adjusted Adjust the pressure plate.
correctly?
The specified values are emission values and do not
necessarily represent safe workplace values. Although
there is a correlation between emission and immission
levels, this cannot be used to infer whether additional
safety measures are necessary or not. Factors which
affect the current immission levels at the workplace,
include the type of room, other sources of noise, e.g.
the number of machines operating and other processes
DBHC002
taking place in the vicinity. Permitted workplace values
230-240 V ~ can differ from country to country. This information is
designed to help the user to better assess the dangers
S6(40%) :2800W
and risks.
II
Note: The product is intended
IPX4
for use only in properties having a
-1
60 min
mains current carrying capacity of
44 mm
≥100 A per phase and being sup-
92 dB(A)
plied by a distribution network
70.3dB(A)K=3dB(A)
with a mains voltage of 230 V. If
required, contact the electricity
92.4dB(A) K=2.45dB(A)
company to ensure that the mains
20.8 Kg
current carrying capacity at the
connection point to the public
power grid is adequate for con-
necting the product.