monzana DBHC002 Manuel page 11

•If you wish to use an extension cable, ensure
that the cable is suitable for the purpose and has
Otherwise this may
cause a loss of performance in the product and
unsure, contact a specialist.
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of
electric shock.
•If you cannot avoid using an electrical tool in a
damp environment, ensure you use a residual
current device with a trigger current of 30 mA or
less. Use of an RCD reduces the risk of electric
shock. NOTE: The term "residual current device
(RCD)" may be replaced by the term "ground
fault circuit interrupter (GFCI)" or "earth leakage
circuit breaker (ELCB)".
•Do not force the product. Use the appropriate
power tool for the task in hand. The correct
rate for which it was designed.
•Do not use the power tool if the switch does
not turn it on and off. Any power tool that
cannot be controlled with the switch is danger-
ous and must be repaired.
•Disconnect the plug from the power source
product. reduce
•Store power tools that are not in use out of the
reach of children. Do not allow persons unfamiliar
Power tools are dangerous in the hands of untrained
users.
•Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
before using the product. Many accidents are
caused by badly maintained power tools.
•Use the power tool, accessories and other tools
be carried out.
•Use of the power tool for purposes for which it
was not intended may result in a hazardous
turning the product on.
result in personal injury.
•Avoid switching on accidentally. Ensure that
the product is switched off before you connect it
to the power supply or carry it anywhere. When
carrying the product, having your finger on the
switch or the unit switched on and connected to
the power supply, may lead to accidents.
Safety notes for the shredder
•Check before switching on whether the blades
•Never use the product without the feed
hopper.
•If the product is blocked, first switch off the
device, disconnect the plug from the mains and
removing the blockage. Keep the On / Off switch
clean and free from foreign objects.
•Before switching on, the product must have
•Check before switching on whether all screws,
onto material being cut while the blade is
Remove cut materials that are
switched off.
www.Deuba24online.de
blade. Keep hands and feet away from the
openings when the machine is running.
•Make sure that the feed hopper is empty
Take
objects (such as stones, glass, metal, earth,
product. This may blunt the blades and damage
the motor.
mechanism or the product makes unusual
noises or vibrates abnormally, immediately stop
the motor and allow the product to come to a
•Never put hands, other parts of the body or
or in the vicinity of other moving parts.
•Always remove the cut material from the
avoid blocking the product or allowing cut
material to enter the feed hopper opening via
kickback. This may lead to accidents.
there should be no people or animals as they
may be hurt by flying objects.
•Do not operate the product on paved or
cemented areas. The cut material may rebound
and cause injuries.
the motor is running.
the product runs for approximately 5 seconds.
•Ensure that the On/Off switch is set to Off
when you put the plug into the socket.
when working with the product. Never stand
higher than the product when feeding in material.
20 21 www.Deu b a2 4 o n lin e.de
Product overview
Figure 1
1.Feed hopper
2.Push bar
3.Handle
6.On/Off switch
7. Power cord with plug
8.Clearance adjustment screw
10.Frame
11.Axle
12.Wheels
Unpacking and assembly
Unpack the product and make sure all of the
pieces are there.
In this way, you
Scope of delivery
•Shredder
•Frame bars
•Axle
•Wheels (2x)
•Push bar
Assembly
DANGER! Risk of injury!
The product must be assem-
bled on an even, flat and solid
surface. You will need at least
two people to assemble the
product.
Assembling the undercarriage
Figure 2
– Push the axis (11) through the frame bars (10).