BH HIPOWER sportkoncept SK LINE G930 Instructions De Montage Et Utilisation page 9

1. ASSEMBLY INSTRUCTIONS.-
Take the unit out of its box and make sure that all of
the pieces are there, Fig.1:
(69) Main post with handlebar and monitor; (1) Main
body; (44) Rear central post cover; (44) Front
central post cover; (110-111) Bottom trim covers,
left and right (L & R) for the knuckle joints on the
focus bars; (101) Knuckle joint spacers; (133) Screw
M-5x10; (112) Screw M-4x50; (102) Screw M-
10x70; (103) Self-locking nut M-10; (5) Screw M-
6x10; (8) Allen screw M-10x20; (14) Grower spring
washer M-10; (13) Flat washer M-10 Ø 18; (K)
Combination spanners; (L) Star driver spanner; (LL)
Allen key; (143) The adapter. G-930 15v. 1Amp;
(155) Bottle holder.
2.
FITTING THE MAIN POST.-
Take hold of the post (69) and bring it up to the boss
on the main body (1), connect the terminals (H17-
H82-H84), sticking out of the bottom of the post,
with terminal (26-L04-L06) coming up out of the top
of the tube on the main body (1), Fig.2, now slip the
main post over the boss on the main body in the
direction of the arrow, making sure not to snag any
of the cables.
Take screws (8), Spring washers (14) and flat
washers (13) and screw together as shown in Fig.2
without tightening fully.
3
ATTACHING THE FOCUS BARS TO
THE FOOT BARS.-
Take the bottom section of the focus bar (98R) and
insert the spacer (101) into the knuckle joint at the
bottom end of the bar in the direction of the arrows
Fig.3A.
Having done this bring the focus bar to the foot bar
(154) and insert screw (102) along with washer (13).
Next, fit the washer (14) and screw on the self-
locking nut (103) securely.
Do the same for the left focus bar (98L) with the foot
bar (153).
When everything has been assembled, check that
the monitor works by doing some exercises. If it
works correctly then fully tighten the screws (8)
Fig.2 on the focus bars, that were left hand tight in
step 2 of the assembly instructions.
4.
FITTING THE TRIM CAPS TO THE
KNUCKLE JOINTS.-
Take the two trim caps (110-111), marked on the
inside with the letter (R) and fit them onto focus bar
(98R), as shown in Fig.4A. Next use screw (133) to
screw the caps onto the focus bars and use screws
(112) to screw the caps together.
Do the same with the trim caps (L) for focus bar
(98L).
5
FITTING THE CENTRAL COVERS.-
.
Take the front (44) and rear (44) covers and position
them on the main post (69), Fig.5. Now use the
screws (141) to attach them to the post.
6.
BOTTLE HOLDER ASSEMBLY.-
Remove screws (156) located on the main post (69)
Fig.6, position the bottle holder (155) and secure it
by using the screws removed previously.
7.
LEVELLING.-
Once the unit has been placed into its final position
for doing exercise, make sure that it sits flat on the
floor and that it is level. This can be achieved by
screwing the adjustable support blocks (120) up or
down, as shown in Fig.7.
8.
MOVEMENT & STORAGE.-
The appliance is equipped with wheels (125) making
it easier to move about. The two wheels at the front
of the appliance make it easy to store the machine
away, as shown in Fig.8.
9.
PULSE MEASUREMENT.-
Your pulse rate is measured by placing both hands
on pulse sensors (148) located on the seat
handgrips or the handlebar, see Fig.9.
NOTE:
You can also use the chest band (OPTIONAL
TELEMETRIC PULSE SENSOR) to measure your
heart rate.
The reading from the telemetric pulse rate takes
preference over the pulse sensors (148) located on
the seat handgrips or handlebar.
10.
BATTERY CHARGE.-
Before starting the battery charge, make sure that
the mains voltage is compatible with the AC/DC
adaptor.
Connect the AC/DC adaptor (143) to the mains.
Then, connect the DC terminal to the connector
located at the low end of the chain cover Fig.10.
BH RESERVES THE RIGHT TO MODIFY THE
SPECIFICATIONS
WITHOUT PRIOR NOTICE.
8
SK
LINE
sportkoncept
OF ITS PRODUCTS