Asist AE1P90DN-BMC Mode D'emploi page 40

If your drill does not work, check its mains connection.
If the drill does not drill correctly, check the sharpness
of the drill bit, replace the drill if it is worn. Make sure
the bore is set to forward for normal use.
If the fault cannot be rectified, have the drill repaired
by an authorized service center.
CLEANING AND MAINTENANCE
! Before cleaning and maintenance, always unplug
the tool.
Your tool requires no additional lubrication or mainte-
nance. There are no parts that you can repair.
Never use water or chemical cleaners to clean your
tools. Wipe it with a dry cloth.
Keep the motor fan frames clean.
If you see a very faint spark in the engine compart-
ment, your tool is OK. Increased sparking is a fault in
the engine.
Never clean any part of the tool with a hard, sharp or
rough object.
Storage when not used for a long time
Do not store the tool in a place where the temperature
is high.
If possible, store the tool in a place with a constant
temperature and humidity.
SPECiFiCATiONS
Input voltage
Input frequency
Power consumption
Idle speed
number of strokes:
Weight
Maximum borehole diameter up to:
steel
wood
concrete
Chuck
Protection class
Sound pressure level measured according to EN
60745:
LpA (sound pressure) 92 dB (A) KpA=3
LWA (sound power) 103 dB (A) KwA=3
Take appropriate measures to protect your hearing!
Wear hearing protection whenever the sound pressure
exceeds the level of 80 dB (A).
Weighted effective acceleration according to EN
60745:
13,90 m/s2 K=1.5
Caution: The vibration level may vary during power
tool operation from the declared value depending on
the way the power tool is used and depending on the
following conditions: Method of power tool use and
type of material being cut or drilled, conditions of the
power tool and method of its maintenance, appro-
priateness of the used accessories and ensuring its
sharpness and good conditions, the strength of handle
gripping, use of anti-vibration equipment, suitability of
230 V
50 Hz
900W
0-3000 rpm
48000 min-1
1.9 kg
10 mm
25 mm
13 mm
13 mm
II.
the power tool for the purpose for which it has been
designed and compliance with workflows according to
manufacturer's instructions.
If this power tool is used in an inappropriate manner, a
hand/shoulder vibration syndrome may appear.
Caution: For clarification, it is necessary to consider
the level of vibrations in specific conditions of use in all
operating modes, e.g. the time when the power tool is
switched off except for the operation time, and when
it idles, i.e. performs no work. This may substantially
decrease the exposition level during the whole operat-
ing cycle.
Minimize the risk of vibrations, use sharp chisels, drill
and blades.
Keepthe power toolin compliancewith theseinstruc-
tions and provide for its proper lubrication.
When using the power tool regularly, invest into anti-
vibration equipment.
Do not use the power tool under temperatures lower
than 10°C. Plan your project containing work with the
power tool producing high vibrations carefully and
spread it over more days.
Subject to changes.
ENViRONmENTAL PROTECTiONWASTE mA-
NAgEmENT
Power tools, accessories and packaging should be
provided for recycling and not to harm the environment.
Do not dispose of power tools into household waste!
According to Directive 2012/19/EU of the European
Parliament and of the Council on waste electrical and
electronic equipment (WEEE) and its approximation
in national laws, unfit power tools must be handed
over at the point of purchase of similar equipment, or
in available collection points designated for collection
and disposal of power tools. Such disposed power
tools will be collected, disassembled and delivered for
environment-friendly recycling.
WARRANTY
In the attached material, you will find our warranty
conditions.
Date of manufacture
The date of manufacture is incorporated into the serial
number stated in the product nameplate.
The serial number has the format of ORD-YY- -SERI,
where ORD is the number of purchase order, YY
stands for the year of manufacture,
of manufacture and SERI means the serial product
number.
40
is the month