Publicité
Les langues disponibles
Les langues disponibles
Installation and operating instructions
EN
Name
No.
29 Ventilation profile - "Intensive ven-
tilation" - Control CO
30 Ventilation profile - "Intensive venti-
lation" - Fan level
31 Ventilation profile - "Intensive venti-
lation" - Fan level
32 Ventilation profile - "Intensive venti-
lation" - Target temp. Supply air
33 Ventilation profile - "Intensive venti-
lation" - Target temp. Supply air
34 Ventilation profile - "Fireplace mo-
de" - Activate
35 Ventilation profile - "Fireplace mo-
de" On/Off
36 Ventilation profile - "Fireplace mo-
de" Interval
37 Ventilation profile - "Fireplace mo-
de" - Extract air
38 Ventilation profile - "Fireplace mo-
de" - Extract air
39 Ventilation profile - "Fireplace mo-
de" - Supply air
40 Ventilation profile - "Fireplace mo-
de" - Supply air
41 Heat exchanger - Heat recovery
42 Heat exchanger - Cooling
43 Heat exchanger - Bypass
Name
No.
51 Temperature sensor - Extract air
52 Temperature sensor - Supply air
53 Temperature sensor - Exhaust air
54 Temperature sensor - Intake air
55 Temperature sensor - Heat excha.
56 Humidity sensor - Extract air (intern) Status val.
57 Humidity sensor - Max. meas. val.
58 CO2 sensor - Max. measured val.
No.
Name
61 Date - Last filter replacement
62 Date - Last filter replacement
63 Filter replacement - Alarm
64 Emergency function - Alarm
NOTE
Data transfer
Delta Temperature (K)
Delta relative humidity (%)
Delta CO
concentration (ppm)
2
Delta VOC concentration (ppm)
Cyclical transfer
– Transfer cycle (min)
Wait for transfer after resetting the
bus voltage
– Wait time (s)
KNX-Module KWL-KNX Connect
Function
Status
concentration
2
Setpoint
Status
value
Setpoint
Status
value
Trigger
Status
Trigger
Setpoint
Status
value
Setpoint
Status
value
Status
Status
Status
2.4 Sensors
Function
Status val.
Status val.
Status val.
Status val.
Status val.
Status val.
Status val.
2.5 Maintenance
Function
Setpoint
Status val.
Status
Status
2.6 Parameters
The values printed in bold are the factory setting values.
Parameters
1, 2, 3, 4, 5
1, 2, 5, 7, 10
100, 200,
300, 400
100, 200, 400 0x4613
Yes / No
1, 2, 5, 10,
15, 30
Yes / No
30, 60
DPT
Length Direct. Description
DPST-1-1
1 Bit
OUT
DPST-5-1
1 Byte IN
DPST-5-1
1 Byte OUT
DPST-9-1
2 Byte IN
DPST-9-1
2 Byte OUT
DPST-1-17 1 Bit
IN
DPST-1-1
1 Bit
OUT
DPST-1-17 1 Bit
IN
DPST-5-1
1 Byte IN
DPST-5-1
1 Byte OUT
DPST-5-1
1 Byte IN
DPST-5-1
1 Byte OUT
DPST-1-1
1 Bit
OUT
DPST-1-1
1 Bit
OUT
DPST-1-1
1 Bit
OUT
DPT
Length Direct. Description
DPST-9-1
2 Byte
OUT
DPST-9-1
2 Byte
OUT
DPST-9-1
2 Byte
OUT
DPST-9-1
2 Byte
OUT
DPST-9-1
2 Byte
OUT
DPST-9-7
2 Byte
OUT
DPST-9-7
2 Byte
OUT
DPST-9-8
2 Byte
OUT
DPT
Length Direct. Description
DPST-11-1 3 Byte
IN
DPST-11-1 3 Byte
OUT
DPST-1-5
1 Bit
OUT
DPST-1-5
1 Bit
OUT
Description
0x4610 This parameter defines the difference between the last transferred value and
the current value, which is required for a new value transfer (objects 51 - 55)
0x4611 This parameter defines the difference between the last transferred value and
the current value, which is required for a new value transfer (objects 56 - 57)
0x4612 This parameter defines the difference between the last transferred value and
the current value, which is required for a new value transfer (object 58)
This parameter activates / deactivates the cyclical transfer of the sensor
values (objects 51 - 58)
0x4614 This parameter defines the time after which a sensor value is transferred
again (objects 51 - 58)
If this parameter is set to yes, the transfer of OUT objects is suppressed for
a waiting time after resetting the bus voltage
0x4615 This parameter defines the waiting time after which all OUT objects transfer
3
their values
Status information: CO
control for "Intensive ventila-
2
tion" active/inactive
Set fan level for "Intensive ventilation"
Fan level for "Intensive ventilation"
Set target supply ait temperature for "Intensive
ventilation"
Target supply ait temperature for "Intensive venti-
lation"
Activate ventilation profile "Fireplace mode"
Status information: "Fireplace mode" active or
inactive
Activate "Fireplace mode" for configured time
NOTE: If the configured time is e.g. 2 min, the real
interval time lies between 2 and 3 minutes.
Set extract air fan level for "Fireplace mode"
Extract air fan level for "Fireplace mode"
Set supply air fan level for "Fireplace mode"
Supply air fan level for "Fireplace mode"
Status information: "Heat recovery" is active
Status information: "Cooling" is active
Status information: "Bypass" is active
Measured value: Temperature sensor Extract air
Measured value: Temperature sensor Supply air
Measured value: Temperature sensor Exhaust air
Measured value: Temperature sensor Intake air
Measured value: Temperature sensor Heat exchanger
Measured value: RH sensor (internal)
Measured value: RH sensor
Measured value: CO2 sensor
Set date of last filter replacement
Date of last filter replacement
Alarm information: Replace filter
Alarm information: Emergency function is active
Publicité
