Altrad ATIKA KGSZ 305 N Notice Originale page 14

Residual risks
Even if used properly, residual risks can exist even if the
relevant safety regulations are complied with due to the design
determined by the intended purpose.
Residual risks can be minimised if the "Safety information" and
the "Intended usage" as well as the whole of the operating
instructions are observed.
Observing these instructions, and taking proper care, will reduce
the risk of personal injury or damage to the equipment.
 Danger of injury of fingers and hands by the tool (saw blade)
or work piece, e.g. when replacing the saw blade.
 Injury from parts of the workpiece spinning off.
 Throwback of the workpiece or workpiece parts.
 Breakage and expulsion of saw blade.
 Risk from electricity, by using non-standard electrical
connections.
 Touching live parts of opened electrical components.
 Impairment of hearing when working on the machine for
longer periods of time without ear protection.
 Emission of harmful timber dust when operating without
exhaust suction.
In addition, in spite of all the precautionary measures taken,
non-obvious residual risks can still exist.
Safety instructions
Read all safety warnings and all
instructions. Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious injury.

For safety instructions, please refer to the enclosed
brochure "Safety instructions for crosscut and mitre saws".
Keep the instructions in a safe place for future use.
Description of device /
Spare parts
 Please refer to the attached assembly and
operating instruction sheet.
Pos. Order-no.
1  Handle with On/Off switch
1A  On/Off switch
1B  Laser switch
2  Carrying handle
3  Motor
4 366066 Carbon brush cover
5  Transport locking pin
6  Set screw for the pulling device
7 366054 Handle for rotary table
8  Rotary table
9 366055 Table insert

10 Indicator for mitre angle
11 366056 Work piece stop
14
Designation
Pos. Order-no.
11A 366057 RH additional stop
11B  Locking screw for RH additional stop
11C 366058 LH attachment
11D  Locking screw for LH attachment
12  Set screw for work piece stop
13  Laser head
14  Locking screw for the laser
15  Protective cover
16  Pendulum cover
16A  Holder for the pendulum cover
17  Lock for pendulum cover
18 366086 Workpiece support
19  Fastening screw for workpiece support
20 Vice assembly
366060
22 Star grip
23 366011 Dust bag
24  Exhaust neck
25  Incline angle locking knob
25A  Anti-swivel device
26  Scale for incline angle
27  Indicator for incline angle
28  Set screw for 90° saw head incline
29  Locking nut for set screw (90°)
30  Set screw for 45° saw head position
31  Locking nut for set screw (45°)
32  Set screw for the saw blade position
33  Locking nut for set screw (saw blade
position)
34 366020 Hexagonal screw for saw blade mounting
35 366073
Front saw blade flange
36 366053
Saw blade (Ø 305 x 30 x 2.8 x 60T)
37 366075
Rear saw blade flange
38  Saw blade locking device
39  Montage-holes
40A  Front stand
40B  Counter nut for front stand
41  Adjusting screw for 45° incline (RH)
42  Locking nut for adjusting screw (45° RH)
43 366077
Carbon brush
44  Installation wrench
45 366062 Warning label 1
46 363977 Warning label 2
47 366061 Safety label
Preparing for commissioning
 To achieve flawless functioning of the machine, please
follow the instructions listed:
 Place the machine at a location that meets the following
conditions:
 secured against slipping
 free of vibrations
 even
 free of tripping hazards
 adequate light
Designation