Altrad ATIKA KGSZ 305 N Notice Originale page 13

Symbols Operating instructions
Threatened hazard or hazardous situation. Not
observing this instruction can lead to injuries or cause
damage to property.
 Important information on proper handling. Not
observing this instruction can lead to faults in the
machine.
User information. This information helps you to use all

the functions optimally.
Assembly, operation and servicing. Here you are
explained exactly what to do.
Please refer to the attached assembly and
operating instruction sheet for references to
figure numbers in the text.
...
Symbols machine
Carefully read operator's manual before handling
the machine. Observe instructions and safety rules
when operating.
Wear eye and ear protection.
Wear dust mask.
Risk of injuries of fingers and hands by the saw
blade.
Do not expose to rain. Protect against humidity.
Shut off engine and remove power cord
before performing cleaning, maintenance or
repair work.
Attention! Laser radiation. Do not look into the
beam.
Danger area! Keep hands, fingers or arms away
from this area as much as possible.
This product complies with European regulations
specifically applicable to it.
Machine of the protection class II (double insulated)
Electrical devices do not go into the domestic rubbish.
Give devices, accessories and packaging to an
ecofriendly recycling.
According to the European Directive 2002/96/EC on
electrical and electronic scrap, electrical devices that are no longer
serviceable must be separately collected and brought to a facility
for an environmentally compatible recycling.
Characteristic noise values
DIN EN ISO 3744 / DIN EN ISO 11202 / ISO 7960 Appendix A
Use of machine as crosscut and mitre saw with standard saw
blade.
Noise power level
Operation L = 109.0 dB(A)
WA
under load
The factor of measurement uncertainty is 3 dB.
The values given are emission values and must therefore not simulta-
neously represent safe workplace values too. Although there is a
relationship between emission and immersion levels, it can be reliably
deduced whether additional precautionary measures are necessary or
not. Factors, which can influence the immersion level currently existing
at the workplace include the duration of the effects, the special type of
the workroom, other noise sources, etc. e.g. the number of machines
and other adjacent processes. The permissible workplace values can
also vary from country to country. This information should however
enable an improved assessment of the danger and risk to be carried
out.
Normal intended use
 The device is suitable to cut wood and other wood-type
materials (e.g. particle boards) in the house and hobby field.
 The device is suitable for crosscuts, inclined cuts, mitre cuts
and double mitre cuts.
 The cutting of round material and irregularly shaped
materials (rickers, poles, fire wood etc.) is not permitted
since these work pieces cannot be held securely.
 Only work pieces that can be put down securely and held
with clamping devices may be processed.
 The use of saw blades made of HSS steel (high-alloy high
speed steel) is not permitted since this steel is hard and
brittle. Risk of injury through saw blade breakage and
expulsion of saw blade pieces.
 The intended usage also includes compliance with the
operating, servicing and repair conditions prescribed by the
manufacturer and following the safety instructions included in
the instructions.
 The relevant accident prevention regulations for the
operation as well as the other generally acknowledged
occupational medicine and safety rules must be complied
with.
 Any other use is deemed not to be use as prescribed. The
manufacturer is not liable for any type of damage resulting
from this: the user bears the sole risk.
 Independently made alterations to the circular saw preclude
any liability of the manufacturer for resulting damages of any
kind.
 The circular saw may only be equipped, used and serviced
by persons who are familiar with these and have been
instructed in the hazards. Repair works may only be carried
out by us or by a customer service agent nominated by us.
 The machine may not be used in a potentially explosive
environment or be exposed to the rain.
 Metal parts (nails, etc.) must be removed from the timber to
be sawn.
Sound pressure level at the
workplace
L = 96.0 dB(A)
PA
13