Publicité
Les langues disponibles
Les langues disponibles
When the vacuum level is reached, the welding start automatically .
3
After welding the unit stops. Cut the roll and use like a bag.
To have a good first seal of the roll, use always automatic cycle.
VACUUM PACKAGING IN CONTAINER
(containers provided with vacuum valve are required for this operation; only containers suitable for vacuum packaging, in plastic material or
toughened glass, shall be used).
- Set on Manual cycle
- Lift the cover.
- Introduce the adapter hose into the air suction plugs.
- Fill the container leaving at least 3 cm. free room from the upper rim and place the cover on it.
- Slightly unscrew the cover cap so as to unlock the valve (attention: the cap must not be unscrewed completely, some turns are enough).
- Place the adapter for containers on the cap.
- Start up the air pump by pressing switch until the desired vacuum level is reached.
- Stop machine, remove the adapter for containers from the container cover and screw the cap until the valve is locked.
- To open the container, slightly unscrew the cap to unlock the valve; then move the valve to let air into the container.
VACUUM PACKAGING WITH REBER UNIVERSAL COVERS
(REBER universal covers are available in different sizes to be suitable for containers, jars, bowls, pots and pans of common domestic use, with
diameters from 4 to 22 cm.)
- Operate as described for vacuum packaging in container, making sure that the container edge perfectly adheres to the universal cover gasket.
- In case of prolonged use on the same container, the cover gasket may show a groove caused by container edge. To avoid any problems, turn the
gasket upside down: the groove will disappear in a short time.
- The gasket can be removed to washing purposes. After drying, place it correctly in its seat;gasket can be washed only by hand, never in dishwasher.
ELECTRONIC SETTINGS
Default set:
1-
Default e lectronic power of sealing of 5 units time/power , suitable for 95/105 microns bags fournished
2-
The power of the seal can be changed by electronic setting.
3-
The machine is settled in automatic cycle vacuum/seal,
4-
It is possible to pass on manual cycle by programming the electronic card.
5-
The machine is settled by a waiting time of 3 sec. from the reaching of the vacuum level and the starting of the seal cycle to obtain more
vacuum; it is possible to change this time by programming the electronic card.
6-
The machine is settled by a waiting time at the end of the seal cycle to obtain a best quality seal; this waiting time can be stopped by press
the Start cycle switch (1) when the Led (if there is) switch off indicated the seal cycle is finished
INFO:
Sealing time could be different using different kind of bags even if thickness is the same; we suggest to test welding after changing welding time.
Less seal power = faster cycle.
IMPORTANT
If the machine is not used for a long period and/or in the case of non-adequate or low temperatures, it is recommendable, before using the machine, to
try it once without using the bag and keep the machine working in automatic cycle for one/two cycles.
SEAL POWER SETTING
1-
With the appliance connected to the power supply
2-
Push 10 times in 10 seconds the seal switch (2), green led ( if present ) will light on fast to indicate you are entered in setting mode
3-
If green led do not light fast, re-start from point 1
4-
Push the pump switch (1) once per each unit of time/power you need ( default set is 5 units), green led ( if present) will light once per each
time you push
5-
If pushing on pump switch (1), the pump start, it means the cycle was not correct, re-start from point 1
6-
Wait 10 seconds to start working normally with new seal power set
7-
New set will remains in memory of the machine even if you disconnect the machine from power supply.
SETTING THE MACHINE TO MANUAL/AUTOMATIC USE
To set the machine to manual use, proceed as described below:
Before starting on the power switch 11 or before connecting the plug to power supply for code 9709 NE, press and hold on Start cycle switch ( 1 );
Switch on the power switch 11 or connect the plug to power supply;
Wait for at least 5 seconds;
Release the switch.
To set the machine to automatic use, proceed as described below:
Before connecting the plug to power supply, press and hold on Seal switch ( 2 );
Connect the plug to power supply;
Wait for at least 5 seconds;
Release the switch.
(The setting will last when unplugging the machine, until a new programming operation will be made).
SUPERVACUUM SETTING
The machine is default settled by a waiting time of 10 sec. from the reaching of the vacuum level and the starting of the seal cycle to obtain more
vacuum; it is possible to change this time:
Connect the machine
Press and hold on the switches 1 and 2
Publicité
