ADEO SCREEN PROFESSIONAL Manuel D'instructions page 5

page de 21

/ 21
Signets

Les langues disponibles

ENGLISH

This manual is an integral part of the product and must be read and understood in all its parts for safety reasons. It contains norms and directions for

correct and safe use of the screen. The manual should never be separated from the product; it must be stored in a suitable place to ensure its integrity,

and in such a way as to be easily consulted by authorised personnel. Product user shall be responsible for the manual's safekeeping. User shall also

be responsible for checking the screen's functionality and for the repair or replacement of any damaged parts that could pose a hazard.

Images contained in this manual are intended to provide a detailed description of the product's functions, characteristics and procedures. Any slight

difference, depending on the model represented, will not change the meaning that the images convey.

Our screens are manufactured in compliance with the following EC directives: 2006-95-EC low voltage directive (LVD), 2004-108-EC electromagnetic compatibility

(EMC), 1999-05-EC radio equipment and telecommunication terminals (R&TTE).

The projection screen is a cadmium-free plastic pvc sheet, with M1 and M2 fire classification under French standards (LNE Laboratoire national de métrologie et

d'essais – SME Centre de recherches du Bouchet). In the absence of a standardisation at a European level of the various national classification norms, it should be

noted that the French M1 class corresponds to non flammable material and that M2 class corresponds to flame retardant material.

Ensure that the screen has suffered no damage during transport. Promptly report any anomaly to the vendor. Verify that all screen accessories have

been included (see list below).

WARNING do not use cutters or sharp objects to open the wrapping.

Motorised or integrated radio roller screen

-2 Kits of installation brackets (for screens up to 3 m wide)

-3 Kits of installation brackets (for screen over 3 m wide)

-2 lateral brackets (for screen models without case)

-1 10° unipolar, 250V dead man's selector switch with directional arrows,

inclusive of wall mount hood

-1 RF transmitter (for integrated radio screen models)

-1 plastic hex wrench

-1 instructions booklet

(screws and plugs for wall mount are not included)

Always read the instructions and warnings set out in this manual very carefully before using the product or before performing any maintenance

interventions.

- Before and during use, check that the screen poses no risk of hazard.

- Do not tamper with, remove or damage any part or component of the screen.

- Never perform screen maintenance operations when the motor is on (for maximum safety, remove power supply).

All our screens are covered by guarantee; validity of the same shall be subject to user's full compliance with the instructions contained in this manual.

WARNING: Faulty installation may compromise the safety of the product's operators; manufacturer shall not be held liable for damages to persons or

things resulting from faulty installation, improper use, insufficient or inadequate maintenance of the screen.

Manufacturer shall not be held responsible for problems associated with installation errors.

Screen installation, electrical connections and verifications in case of malfunction of motorised rolling screens must be performed by authorised vendor

or by personnel that is informed and trained in electrical hazards. The connection cable cannot be replaced. If the cable is damaged the screen must

be replaced. Tampering with end stops or piercing the seal placed over holes shall entail the forfeiture of the guarantee. For any necessary

clarifications please contact our technical office.

N.B.ONCE THE SCREEN HAS BEEN MOUNTED ON THE BRACKETS, AND PRIOR TO USING IT, USER IS MANDATORILY REQUIRED TO

ENSURE THAT THE SCREEN'S POSITION IS PERFECTLY HORIZONTAL.

Our screens are suitable for indoor use at normal temperature (20 - 25 ° C) and humidity conditions. Special precautions are necessary for outdoor

use, especially as regards temperature levels and the presence of dust. Exposure to temperatures of over 50 ° C can cause permanent deformation of

the screen's flatness, or the screen to come away from the roller.

Avoid prolonged exposure of the projection screen to solar light to prevent yellowing of the same (ensure that exposure to solar light does not cause

the screen to reach said temperature level).

Since electrostatic charge tends to accumulate on the projection screen (which is made of PVC), attracting dust, excessive dustiness in the projection

environment can deteriorate the optical quality of the screen (see projection screen cleaning instructions).

WARNING: Do not manually force the screen's unrolling: this could result in the motor being damaged or the screen's case to come away from the wall

mount brackets.

Do not allow children to play with the screen's control panel. Keep remote control out of children's reach.

Monitor screen movement and allow no-one near it until it is completely closed.

The following operations: blocking, preventing or forcing the screen's movement, hanging or swinging from it, adding or applying any object to the

screen or backdrop, modifying the screen's structure – are strictly forbidden and could result in damages to the screen's rolling system and ensuing

hazard to persons and things.

Remove dust from the case with a soft, clean cloth and a non aggressive detergent as necessary.

Clean the projection screen with a soft, clean, damp cloth, and a neutral or alcohol-base detergent as necessary. Since rubbing the screen with a cloth during cleaning

operations can cause electrostatic charge to accumulate, we recommend the subsequent application of an antistatic liquid with a clean cloth, to avoid dust being

attracted again. Periodically check the mounting system and electrical connections.

CASE MODEL

WALL INSTALLATION:

Fig. 2 and 3

Insert screw 4 with thread turned upwards into plate 1 and screw on nut 3 loosely, leaving a 4-5 mm play; hook plate 1 to the case and insert plastic pin

2 into the slot of the small bracket. Please note that, for assembly purpose, the plate can be mounted either way since the hookable sections of the

case are perfectly symmetrical. Secure bracket 5 to the wall with adequate wall type expansion plugs (min. Ø 8 mm) and secure plate 1 to bracket 5

using washer 7 and bolt 3.

CEILING INSTALLATION:

secure ceiling brackets 6 (provided) with adequate wall expansion plugs (min. Ø 8 mm), at approx. 10 - 15 cm from the ends of the case. For screens

wider than 350 cm, the third bracket must be positioned in the middle of the case. Insert screw 4 with thread turned upwards into plate 1 and screw on

nut 3 loosely, leaving a 4.5 mm play; hook plate 1 to the case and insert plastic pin 2 into the slot of the small bracket. Secure plate 1 to bracket 6

usando washer 7 and bolt 3.

Direct ceiling installation with mount plates:

For closer adherence of the case to the ceiling it is possible to fix mount plates 1 directly to the ceiling (N.B.: for quick and easy performance of this

operation, excellent ceiling flatness and perfect alignment of the plates are required). Secure the plates with expansion plugs suitable for the type of

ceiling (min. Ø 8 mm), at approx. 10 - 15 cm from the ends of the case. For this type of installation, as a rule, the side of the plate in which the pin is to

be slotted should be turned towards the front of the case, to facilitate the insertion of the pin. Carefully check the alignment and horizontality of the

plates. Metal washers of the type included in the packaging may be used for the purpose as necessary. Note that an accurate performance of this

operation will ensure ease and speed when subsequently hooking the case to the plates. For screens wider than 350 cm the third palte must be

positioned in the middle of the case. Hook the case to the plates with a semicircular movement (until it clicks into position); secure the case to the

plates by inserting the plastic pins.

1) fasten bracket 8 with adequate expansion plugs (min. Ø 8 mm); ceiling or wall mount are possible;

MODEL

2) fasten bracket 9 to motor with relevant screws (provided); temporarily insert the roller into the pin of bracket 8, so as to calculate the distance

WITHOUT

between the two brackets on the wall; after marking the exact position of the holes on the wall, remove the screen;;

CASE

3) fasten motor-side bracket 9 (to wall or ceiling) with suitable expansion plugs (min. Ø 8 mm);

4) insert round pivot in relevant slot of bracket 8 and plug the slot with split pin (provided);

Fig. 6

5) secure motor head to motor side bracket with relevant screws 5.

INTRODUCTION

GENERAL CHARACTERISTICS OF THE PRODUCT

UNPACKING THE SCREEN

GENERAL SAFETY NORMS

WARNINGS AND RECOMMENDATIONS FOR CORRECT USE