Genius SPRINT 382 Instructions Pour L'emploi page 17

Display Function
Electric lock command and 'traffic lights'
functions:
If you press key - from the
command for the
is activated;
If you press - again, the command for the
closing and opening electric lock is set;
if you press the - key again, you can set the
'traffic lights' functions
= Standard indicator-light
from to
= electric lock command before
opening movement
= electric lock command before
opening and closing movements
= 'traffic lights' function: the output is
active in "open" and "open on pause" status
and is disabled 3 seconds before the closing
manoeuvre starts.
Note: there is 3 seconds of pre-flashing before
the closing manoeuvre.
= 'traffic lights' function: the output is
active only in "closed" status.
Attention: do not exceed the output's
maximum load (24Vdc-3W). If necessary,
use a relay and a power supply source
outside the equipment.
CLOSING PHOTOCELLS LOGIC:
Select the tripping mode of the closing
photocells.
They operate for the closing movement
only: they stop movement and reverse it
when they are released, or they reverse it
immediately.
= Reverse on release
= Reverse immediately when opening
OPENING PHOTOCELLS LOGIC:
Select the tripping mode of the opening
photocells.
They operate for the opening movement
only: they stop the movement and restart
it when they are released, or they reverse it
immediately.
= Reverse immediately when closing
= Restart movement on release
ENCODER:
If the encoder is used, you may select its
presence.
If the encoder is present and enabled,
"decelerations" and "partial opening" are
controlled by the encoder (see relevant
paragraphs).
The encoder operates as an anti-crushing
device: If the gate strikes an obstacle during
opening or closing, the encoder immediately
reverses gate leaf movement for 2 seconds.
If the encoder operates again during the 2-
seconds reversing time, it stops movement
(STOP) without commanding any reversing. If
no sensor is supplied, the parameter must be
set on . If there is the encoder, adjust the
sensitivity of the anti-crushing system, by varying
the parameter between
sensitivity) and
from to
sensitivity adjustment
= Encoder disabled
setting, the
closing electric lock
and .
= Timed output.
(maximum
(minimum sensitivity).
= Encoder active and
Display Function
Pre-limit switch DECELERATION:
You can select gate deceleration before
the opening and closing limit-switches
have been tripped.
Time can be adjusted from
If an encoder is used, the adjustment is not
determined by time but by motor revs, thus
obtaining greater deceleration precision.
= Deceleration disabled
from to
Post-limit switch DECELERATIONS:
You can select gate deceleration after the
opening and closing limit-switches have
been tripped.
Time can be adjusted from
sec. in 0.04-second steps.
The maximum value of
about 7 cm.
If an encoder (optional) is used, the
adjustment is not determined by time but
by motor revs, thus obtaining greater
deceleration precision.
= Deceleration disabled
from to
PARTIAL OPENING:
You can adjust the width of leaf partial
opening.
Time can be adjusted from
sec. in 0.1-second steps.
If an encoder (optional) is used, the
adjustment is not determined by time but
by motor revs, thus obtaining greater
precision of partial opening.
E.g. for a gate with a sliding speed of 10 m
/min, value
metres of opening.
E.g. for a gate with a sliding speed of 12 m
/min, value
metres of opening.
WORK TIME:
We advise you to set a value of 5 to 10
seconds over the time taken by the gate to
travel from the closing limit-switch to the
opening limit-switch and vice versa. This will
protect the motor against any overheating
if a limit-switch fails.
Adjustable from
one-second steps.
Subsequently, viewing changes to minutes
and tens of seconds (separated by a point)
and time is adjusted in 10 second steps, up
to a maximum value of
E.g. if the display shows
min. and 50 sec.
Attention: the set value does not exactly
match the motor's maximum operating time,
because the latter is modified according to
the performed deceleration spaces.
15
ENGLISH
to
= Deceleration enabled
to
corresponds to
= Deceleration enabled
to
corresponds to about 1.7
corresponds to about 2
to sec. sec. in
minutes.
, work time is 2