Publicité
Les langues disponibles
Les langues disponibles
Star Button
Option 5 Off
Not used
Using the Light and Star button on keyfobs to trigger
outputs
1.
To enter programming mode, press *8 followed by 9713.
2.
Press 32# to program the RF Receiver module.
3.
Enter the transmitter number followed by #. For example,
for transmitter 4 enter 4#.
4.
In segment 1 of this location, switch bit 4 and bit 5 On to
enable the Light and the Star button.
5.
Press * to save the setting and # to leave the menu.
You must then program the corresponding event in table 8 so
that pressing the button on the keyfob activates the output.
Programming the Quik Bridge®
Table 7 displays the 17 locations that can be programmed on
the Quik Bridge®.
Table 7: Quik Bridge® output locations and segments
Location
Segment
Description
0
1-4
Programming code
1
1
Output 1 event
2
Output 1 time
2
1
Output 1 Transmitter selection
2
Output 1 Special Setting
3
1
Output 2 event
2
Output 2 Time
4
1
Output 2 Transmitter selection
2
Output 2 Special Setting
5
1
Output 3 event
2
Output 3 time
6
1
Output 3 Transmitter selection
2
Output 3 Special Setting
7
1
Output 4 event
2
Output 4 time
8
1
Output 4 Transmitter selection
2
Output 4 Special Setting
9
1
Output 5 event
2
Output 5 time
10
1
Output 5 Transmitter selection
2
Output 5 Special Setting
11
1
Output 6 event
2
Output 6 time
12
1
Output 6 Transmitter selection
2
Output 6 Special Setting
13
1
Output 7 event
2
Output 7 time
14
1
Output 7 Transmitter selection
2
Output 7 Special Setting
15
1
Output 8 event
P/N 466-2488 • REV A • ISS 02JUL13
Option 5 On
Location
Output 2 control
16
17
Output event
Enter the number for the event that you wish to program for the
output.
Table 8: Quik Bridge® output events
Data
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Output time
This can be set from 0-255 in minutes or seconds. The unit is
set in the Special Setting segment.
Special Setting
This can be set in the different bits of the segment.
Bit 1: selection of time in seconds or minutes.
• Turn bit 1 on to time the output in minutes.
• Turn bit 1 off to time the output in seconds.
Bit 2: selection of inverted output.
• Turn bit 2 on to invert output activation.
Segment
Description
2
Output 8 time
1
Output 8 Transmitter selection
2
Output 8 Special Setting
1
On if Quik Bridge® tamper is enabled
Event
Zone Open
Zone Tamper
TX Low Battery
TX Lost
TX short supervision fault
Clean me fault
Zone open or tamper (default value)
TX lost or low battery
TX lost, low battery or tamper
Zone open, TX Lost, low battery or tamper
Keyfob disarm
Keyfob arm
Keyfob arm or disarm
Keyfob arm stay
Keyfob exit
Fob fire
Fob Medical
Keyfob panic
Keyfob aux 1 (Option 4 from 'Using the 4 button keyfob)
Keyfob aux 2 (Option 5 from 'Using the 4 button keyfob)
Receiver Jam
Box tamper (receiver or Quik Bridge®)
Receiver communication trouble
Receiver communication trouble, box tamper or jam
Reserved
Reserved
7 / 27
Publicité
