Jacob Jensen 5 Manuel D'utilisation page 12

UK
Congratulations on the purchase of your new JACOB JENSEN
Telephone.
The telephone is designed in Denmark by Jacob Jensen, whose
products have gained international recognition for their original,
simple and classic design. Jacob Jensen has received around 00
prizes from around the world and has 9 products included in The
Design Study Collection and The Design Collection of The Museum of
Modern Art in New York.
The JACOB JENSEN Telephone 5 is suitable for connection to the
TM
public network and works with most PABX switching systems (please
consult your switching system provider for details). The telephone
can either stand or be mounted on the wall and is equipped with
a caller ID function for storing up to 80 numbers. The telephone
is further equipped with a mute function in the handset, on hook
dialling, HI/LOW volume adjustment for the ringing tone, the
handset receiver and for on hook dialling.
Installation
Table stand
The telephone is supplied with a table stand which you attach as the
following (see description on page 5):
. Slide the canals of the table stand into the tracks of the base.
The table stand is mounted when you hear a click.
2. Fit the modular contact of the coiled cord into the plug of the
telephone and handset.
3. There are two telephone line cords enclosed.
Connect the wide line cord to the base and to the battery
compartment (OUT). Connect the narrow line cord to the battery
compartment (IN) and to the telephone wall outlet.
Wall mounting
The telephone can be mounted on the wall as follows:
. Disconnect the coiled cord and the wide line cord from the base.
2. Push the button inside the square hole next to the modular jack
using a pen or a finger, and pull the bracket away from the base at
the same time.
3. Place the telephone on the screws already mounted on the wall
(use the template on page ).
. Reconnect the coiled cord and the telephone line cord to the base.
Fixing .and .replacing .batteries
The Telephone 5 requires four pcs. "AA" batteries (included).
To replace the batteries please do as follows:
. Disconnect the wide and the narrow line cord from the battery
compartment.
2. Open the battery compartment.
3. Install four fresh batteries as indicated by the polarity symbols
(+/-).
. Close the battery compartment and reconnect the wide and the
narrow line cord.
Note: When replacing the batteries the date and time must be set
again. Please see the description below.
Setting .date/time ./ .LCD .contrast/ .LDS/ .area .code/ .Flash .time
Leave the handset on hook when setting date and time.
. Press . The month segment starts to flash.
2. Press in order to set the month.
or
3. Confirm by pressing . Now the date segment starts to flash.
. Press in order to set the date, confirm by pressing
or
and the time segment flashes.
5. Continue this process for setting time and minutes.
6. When the correct date and time is set, confirm by pressing
again.
2
7. After setting date and time, you may select the LCD contrast level
TM
by pressing
push to confirm.
8. After setting the LCD contrast you may set the LDS
(Long Distance Setting) and Area Code. The cursor will flash from
first digit. Press
Push to confirm.
Note: It is highly recommended that users from big countries with
many states or provinces like USA, China etc., carefully read this
section for efficient use of the phone.
When the setting of "Long Distance" and "Area Code" match
with those of the incoming call, these codes will not be stored in
the Caller ID memory and outgoing calls to these numbers can be
made directly from the Caller ID memory without dialling the Long
Distance Code and the Area code.
9. After setting the LDS and Area Code, the LCD displays the standard
European flash time (F00 = 00 ms). If needed, you may change
the flash time (00 ms/20 ms/300 ms/ 600 ms - page 2) - consult
your network provider for details.
Press
or
standby mode.
How .to .make .a .telephone .call
To lift off the handset, gently press on the upper part of the handset
with your index finger and the handset falls into your hand.
. Lift off the handset and wait for the dialling tone.
2. Dial the telephone number.
3. Put down the handset when the conversation is over.
On .hook .dialling
It is possible to make on hook dialling till the call is answered:
. Press and wait for the tone signal.
2. Enter the telephone number.
3. Pick up the handset when the call is answered.
. Put down the handset when the conversation is over.
Talking .timer
When you make a telephone call the telephone displays the duration
of the call. The timer starts to count shortly after the call is begun.
When the handset is put down the timer automatically reverts to
standby mode.
Message .waiting
When one or more messages are recorded the telephone displays
. The symbol is automatically deleted when the message is
tapped.
Note: The Message waiting function requires that your telephone
line is provided with Message/Answer from the network provider.
Caller .ID
The telephone is equipped with a caller ID, which shows and stores
the number of in-coming calls. The number is displayed immediately
after the first ring.
The caller ID is able to store up to 80 numbers. When the memory
is full the oldest numbers are automatically replaced by the new
numbers.
Note: The caller ID function requires that your telephone line is
provided with caller ID function from the network provider.
To .view .caller .ID .memories
Use the
or
memory.
The telephone number with date and time for the call is displayed.
. When the desired LCD contrast is shown,
or
to adjust and
or
and to confirm. The display now returns to
to scroll between the numbers in the caller ID
to move to next digit.