Wurth Master WB 10-A Instructions D'emploi page 11

All manuals and user guides at all-guides.com
OBJ_BUCH-766-001.book Page 11 Thursday, May 8, 2008 10:04 AM
Technical Data
Cordless angle drill/driver
Art. No.
Rated voltage
No-load speed
Max. torque for hard/soft
screwdriving application
according to ISO 5393
Torque adjustment range
Max. screw dia.
Max. drilling dia.
– Steel
– Wood
Weight according to
EPTA-Procedure 01/2003
Noise/Vibration Information
Measured values determined
EN 60745.
Typically the A-weighted sound pressure level of the
product is less than 70 dB(A). Uncertainty K =3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values (triax vector sum) determined
according to EN 60745:
Drilling into metal: Vibration emission value
2
a =2.5 m/s , Uncertainty K =1.5 m/s
h
Screwdriving: Vibration
2
a =2.5 m/s , Uncertainty K =1.5 m/s
h
The vibration emission level given in this information
sheet has been measured in accordance with a
standardised test given in EN 60745 and may be
used to compare one tool with another. It may be
used for a preliminary assessment of exposure.
The declared vibration emission level represents the
main applications of the tool. However if the tool is
used for different applications, with different acces-
sories or poorly maintained, the vibration emission
may differ. This may significantly increase the expo-
sure level over the total working period.
An estimation of the level of exposure to vibration
should also take into account the times when the tool
is switched off or when it is running but not actually
doing the job. This may significantly reduce the
exposure level over the total working period.
Identify additional safety measures to protect the
operator from the effects of vibration such as: main-
tain the tool and the accessories, keep the hands
warm, organisation of work patterns.
8.5.08
Declaration of Conformity
We declare under our sole responsibility that the
WB 10-A
product described under "Technical Data" is in con-
0700 632 X
formity with the following standards or standardiza-
V= 10.8
tion documents: EN 60745 according to the
rpm 0 – 585
provisions
98/37/EC (until Dec. 28, 2009), 2006/42/EC (from
Dec. 29, 2009 on).
Nm 13/5
Technical file at:
Nm 2.6 – 5.2
Adolf Würth GmbH & Co.KG, PFW,
mm 5
D-74650 Künzelsau
Adolf Würth GmbH & Co. KG
mm 8
mm 10
kg 1.1
P. Zürn
Battery Charging (see figure A)
according to
☞
Note: The battery is supplied partially
charged. To ensure full capacity of the bat-
tery, completely charge the battery in the bat-
tery charger before using your power tool for
the first time.
The lithium ion battery can be charged at any time
without reducing its service life. Interrupting the
charging procedure does not damage the battery.
2
,
emission value The Li-ion battery is protected against deep dis-
2
. charging. When the battery is empty, the machine is
switched off by means of a protective circuit: The
inserted tool no longer rotates.
WARNING
machine has been automatically switched
off. The battery can be damaged.
To remove the battery 11 press the unlocking but-
tons 10 and pull out the battery downwards. Do not
exert any force.
The battery is equipped with a NTC temperature
control which allows charging only within a temper-
ature range of between 0 °C and 45 °C. A long bat-
tery service life is achieved in this manner.
Observe the notes for disposal.
of the directives 2004/108/EC,
A. Kräutle
Do not continue to press the
On/Off switch after
English–11
the