Function Setting (Oled Remote) - Fortin FSA-211 Guide Utilisateur

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

FUNCTION SETTING (OLED REMOTE)

Long press the 
Choose [FUNCTION], push the 
Choose the [FUNCTION] (see table below) by pressing the 
go down on the menu, 
Press the 
 button for 0.5 seconds, 
The  and   icons will flash. ( enabled,  disabled), 
Long press the 
The  and   icons will stop flashing,   
The [FUNCTION] is now ON or OFF. (See table below) 
 
[MUTE] 
SILENT MODE
When enabled the siren and horn is not activated when arming or disarming. 
The siren will still activate during panic, shock or when the hood, trunk or a door is 
opened. 
VALET FUNCTION
[VALET] 
Disables  the  remote  starter  and  security  system  (if  installed). 
page 8.
ACTIVE OR PASSIVE ARMING (with the security system installed)
[PASSIVE] 
It  is  possible  to  program  the  immobilizer  in  active  mode  (no  automatic  rearm)  or 
passive  (with  automatic  rearm).  Your  remote  starter  is  configured  by  default  to 
passive  mode  in  60  seconds:  the  remote  starter  will  automatically  arm  60  seconds 
after closing the last door. However, the remote starter will not arm if a door stays 
open. 
Note:  When  the  immobilizer  is  automatically  rearm,  you  can  disarm  the  remote 
starter by simply pressing the UNLOCK button.
[SMART] 
DOOR MONITORING
If the doors are not opened within 30 seconds after disarming the system, the system 
will automatically lock the doors and rearm the system (if installed). The door pins 
must be connected to the system to use this feature.
IGNITION DOOR LOCK
[IG LOCK] 
This  is  an  added  security  feature.  If  the  system  is  installed  with  the  door  locks 
connected,  the  doors  will  automatically  lock  when  the  ignition  key  is  turned  to  the 
ON/RUN position and the foot‐brake is pressed. The doors will automatically unlock 
when the key is turned OFF.
SHOCK SENSOR
[SHOCK] 
Any sensor that is not properly adjusted can trigger a false alarm. Disabling the shock 
sensor is useful when parking on busy or noisy streets that have a lot of vibration.   
 
This  feature  can  be  used  to  disable/re‐enable  the  shock  sensor  (zone  4),  auxiliary 
input  (zone  7)  and  the  tilt  sensor  (zone  8).  A  beep  confirms  the  action:  1  beep 
indicates an activated zone and 2 beeps indicates a deactivated zone.
COLD START TIMER MODE
[TIMER] 
This feature will remote‐start the vehicle every 1.5 or 3 hours and it will run for 3, 5, 
7 or 15 minutes (6, 14 or 30 minutes with a diesel engine) depending on 
programming.  See COLD START TIMER MODE page 10.
TURBO MODE
[TURBO] 
N/A (future use)
[CAR CALL] 
MULTI-VEHICULE MODE
[2ND CAR] 
This feature allows 1 remote to control 2 vehicles. 
NOTE : The 2 vehicles must have an remote‐starter and/or security system installed. 
NOTE : The option must be programmed by your technicien.
 button to enter the MENU,  
 button for 0.5 seconds [SET], 
  button, 
See
TURBO MODE
page 8.
 button to go up and 
3
 
 button to 
See  VALET  MODE 
 

Publicité

Chapitres

Table des Matières
loading

Table des Matières