Virutex MEB250A Mode D'emploi page 9

Table pour plaqueuse de chants

Masquer les pouces

page de 40

/ 40
Signets

Les langues disponibles

10) under the machine to raise it.

Place the table attachments in position:

• Some table attachments (S, Fig. 11) should be

arranged in the desired positions, so that the board

is supported while edgebanding, without the excess

lower edging hitting them when the board is moving.

Remove the trimmer

• Remove the AK97NW trimmer applying the method

used to mount it but in the reverse order. If it is

already incorporated, proceeds as indicated in 5.5

ASSEMBLY 5046703 AK97NW TRIMMER-ROLLER-

PRESSERS, in the reverse order

Remove the support guides:

• Remove the intake and exit guides from the table

(M and L, Fig. 2), by loosening the screws (R, Fig. 2).

Remove the pressers:

• When edgebanding circular boards, it is not pos-

sible to use the presser unit (F, Fig. 1). It should be

removed and placed upside down (F, Fig. 11) so that

it does not get lost.

Edgbanding:

If the PEB200/PEB250 edgebander is ready to band

edges, as explained in section 6, follow the steps

below to edgeband a circular board:

• Turn on the advance switch (IJ, Fig. 2) for the

PEB200. This is located on the handle of the machine.

Turn the handle (IK, Fig. 2) on the PEB250 only and

select the working speed.

• Wait a few seconds for the glue to rise from the

tank to the gluing roller.

• Place the board on the worktop attachments (S.

Fig. 5, 11 and 13) and in front of the pressure roller

(N, Fig. 8 and 11).

• Push the edging through the guides until it reaches

the advance roller, which will transport the duly

glued edging until it exits over the pressure roller.

• Press the board against the edging located on the

pressure roller (N, Fig. 8 and 11), so that the rotating

movement of the latter sets the board advance speed.

• Push the board to the second roller and edgeband

the rest of the board by moving it between the two

rollers (Fig. 12), until the edgebanding process is

finished.

• When reaching the end, you should calculate the

excess to be left and cut the edge using the pedal

(IX, Fig. 2).

• Turn off the advance switch (IJ, Fig. 2) on the

PEB200, or put the handle (IK, Fig. 2) with the PEB250

into the (0) position.

• If you have finished working with the machine,

turn off the main switch (IG, Fig. 2), and press the

button (IY, Fig. 2).

9. EDGBANDING SMALL PIECES WITH RADII

AND SHAPES

Make the same adjustments as for edgebanding

circular pieces, as well as:

Additional adjustments:

Remove the auxiliary pressure roller and its shaft:

• Using a screwdriver, remove the safety ring (IL, Fig.

9) that holds the roller.

• Remove the roller (P, Fig. 9) and the roller shaft

(IM, Fig. 9), unscrewing it by inserting a 4 mm rod

in the hole.

Place the rear attachments in position:

• On some pieces it may be necessary to place some

rear attachments (V, Fig. 2, 5, 12 and 13) at the bottom

of the board exit point and in the desired positions, so

that it is supported during edgebanding, and without

the excess edging hitting them as it advances.

Edgbanding:

If the PEB200/PEB250 edgebander is ready to glue

edges, as explained in section 6, follow the steps below

to edgeband a small board with radii and shapes:

• Turn off the advance switch (IJ, Fig. 2) for the

PEB200. This is located on the handle of the machine.

Alternatively, for PEB250, turn the handle (IK, Fig. 2)

and select the working speed.