Virutex MEB250 Mode D'emploi page 7

• Push the edging though the guides until it reaches
the advance roller, which will transport the duly
glued edging until it exits over the pressure roller.
• Push the board forward to meet the edging when
it comes out of the pressure roller.
• Press the board against the edging located on the
pressure roller, so that the rotating movement of the
latter sets the board advance speed, and keep both
hands on it until the end of the edgebanding process.
• Turn off the advance switch (IJ, Fig. 2) on the
PEB200, or put the handle (IK, Fig. 2) with the PEB250
into the (0) position.
• If you have finished working with the machine,
turn off the main switch (IG, Fig. 2). Depending on
the model.
8. EDGEBANDING CIRCULAR PIECES
Prior adjustments:
Lift the PEB200/PEB250 edgebander so that the glued
edging comes out flush with the table:
• To edgeband circular boards, place the PEB200/
PEB250 edgebander in the position shown in (Fig.
2), but put the attachments (T and U, Figs. 3, 8 and
9) under the machine to raise it.
Place the table attachments in position:
• Some table attachments (S, Fig. 10) should be
arranged in the desired positions, so that the board
is supported while edgebanding, without the excess
lower edging hitting them when the board is moving.
Remove the support guides:
• Remove the intake and exit guides from the table
(M and L, Fig. 2), by loosening the screws (R, Fig. 2).
Remove the Clamp:
• When edgebanding circular boards, it is not possible
to use the clamp (F, Fig. 1). It should be removed
and placed upside down (F, Fig. 10) so that it does
not get lost.
Edgbanding:
If the PEB200/PEB250 edgebander is ready to band
edges, as explained in section 6, follow the steps
below to edgeband a circular board:
• Turn on the advance switch (IJ, Fig. 2) for the
PEB200. This is located on the handle of the machine.
Turn the handle (IK, Fig. 2) on the PEB250 only and
select the working speed.
• Wait a few seconds for the glue to rise from the
tank to the gluing roller.
• Place the board on the worktop attachments (S.
Fig. 3, 10 and 12) and in front of the pressure roller
(N, Fig. 7 and 10).
• Push the edging through the guides until it reaches
the advance roller, which will transport the duly
glued edging until it exits over the pressure roller.
• Press the board against the edging located on the
pressure roller (N, Fig. 7 and 10), so that the rotating
movement of the latter sets the board advance speed.
• Push the board to the second roller and edgeband
the rest of the board by moving it between the two
rollers (Fig. 11), until the edgebanding process is
finished.
• Turn off the advance switch (IJ, Fig. 2) on the
PEB200, or put the handle (IK, Fig. 2) with the PEB250
into the (0) position.
• If you have finished working with the machine,
turn off the main switch (IG, Fig. 2).
9. EDGBANDING SMALL PIECES WITH RADII
AND SHAPES
Make the same adjustments as for edgebanding
circular pieces, as well as:
Additional adjustments:
Remove the auxiliary pressure roller and its shaft:
• Using a screwdriver, remove the safety ring (IL, Fig.
8) that holds the roller.
• Remove the roller (P, Fig. 8) and the roller shaft
(IM, Fig. 8), unscrewing it by inserting a 4 mm rod
in the hole.
Place the rear attachments in position:
• On some pieces it may be necessary to place some
rear attachments (V, Fig. 2, 3, 11 and 12) at the bottom
of the board exit point and in the desired positions,
so that it is supported during edgebanding, and wi-
thout the excess edging hitting them as it advances.
Edgbanding:
If the PEB200/PEB250 edgebander is ready to glue
edges, as explained in section 6, follow the steps below
to edgeband a small board with radii and shapes:
• Turn off the advance switch (IJ, Fig. 2) for the
PEB200. This is located on the handle of the machine.
Alternatively, turn the handle (IK, Fig. 2) for PEB250
only and select the working speed.
• Wait a few seconds for the glue to rise from the
tank to the gluing roller.
• Place the board on the worktop attachments (S,
Fig. 3, 10 and 12) and in front of the pressure roller
(N, Fig. 7 and 10).
• Push the edging through the guides until it reaches
the advance roller, which will transport the duly
glued edging until it exits over the pressure roller.
7