Publicité
Les langues disponibles
Les langues disponibles
6. If you are moving the lock to a new door, install the lock on that
door before continuing.
7. To check that the lock was reset, press the Schlage Button and
enter one of the Default User Codes. If the reset was successful, the
Default User Codes will unlock the deadbolt.
L The lock must be set up again after the reset is complete (see
step 7 set up the lock).
L Z-Wave network settings are maintained through Factory Default
Reset.
10
Z-Wave Functions
10a about Z-Wave
• This lock may be included into any Z-Wave network, from any
manufacturer.
• Listening nodes from any manufacturer can act as repeaters to
extend network range.
• The lock will have limited functionality if included with a non-
secure controller.
• Configuration parameters and association group information can
be found at answers.schlage.com.
L The Z-Wave radio is disabled by default to conserve battery
life. When the lock is included for the first time, the radio is
automatically enabled.
L If you no longer wish to use the lock with a Z-Wave network,
make sure to exclude the lock to conserve battery life.
10b Z-Wave Function descriptions
Include the Lock
Turns the Z-Wave radio on and enrolls the lock.
Verify Lock
Verifies that the lock is included in a Z-Wave
Inclusion
network.
Exclude the Lock
Excludes the lock and turns the Z-Wave radio
off.
To Include/exclude the lock, you must first put your Z-Wave
Controller into inclusion mode:
1. Put the controller or panel in Include/Exclude mode.
L This procedure will vary depending on controller manufacturer.
2. Extend the bolt on the lock and then perform the following:
Include/
Programming
exclude the
lock
L The programming indicator will flash rapidly while inclusion is in
process.
To verify Inclusion:
1. Remove the battery cover. See Install the Batteries.
2. Disconnect the battery connector.
3. Observe the indicator in the center of the printed circuit board while
reconnecting the battery connector.
4. The indicator will blink if the lock is included.
need helP?
Please call customer support before returning the product.
Toll-Free Calling From:
Visit our web site for videos, FAQs and more:
answers.schlage.com
regIsTer Your ProduCT
document your purchase and register your warranty at
registerMyschlage.com
6 Digit
OR
Code
The lock
was
included/
excluded
U.S.A.: (888) 805-9837
Canada: (800) 997-4734
Mexico: 018005067866
11
Programming Procedures
L Determine how long you want
your User Codes to be BEFORE
adding any User Codes. If you
change the User Code length,
all existing User Codes will be
deleted!
1. Open the door and extend the deadbolt before beginning.
2. If you make a mistake, press the Schlage Button to leave
Programming Mode, and then start over.
WrITe Your PrograMMIng Code here For easY aCCess
enTer PrograMMIng
FunCTIon
Mode (Press)
add user Code
delete user
Code
Change
Programming
Code
enable vacation
Mode
disable vacation Mode
enable/disable
Beeper
delete all user
Codes
Removes ALL User Codes from the lock. User Codes cannot be retrieved after they are
Warning
deleted!
enable/disable
lock & leave
The lock
was not
included/
Change user
excluded
Code length
Changing the User Code length will delete all existing User Codes! User Codes cannot
Warning
be retrieved after they are deleted!
enable/disable
auto-lock
Temporarily disable
auto-lock
(deadbolt should be
locked to begin)
restore
auto-lock
Include/exclude
the lock
L Programming Mode will
automatically time out after 30
seconds of inactivity.
FunCTIon sTePs
(Press)
6 Digit
New 4-8 Digit
Programming
User Code
Code
6 Digit
4-8 Digit User
Programming
Code
Code
6 Digit
New 6 Digit
Programming
Programming
Code
Code
6 Digit
Programming
Code
6 Digit Programming Code
6 Digit
Programming
Code
6 Digit
6 Digit
Programming
Programming
Code
Code
6 Digit
Programming
Code
6 Digit
Desired User
Programming
Code Length
Code
6 Digit
Programming
Code
4-8 Digit
Within 5 seconds,
User Code
manually lock and unlock
the deadbolt using the
Relock the deadbolt using the thumbturn.
6 Digit
Programming
Code
The lock was
included/
excluded
verIFY
Same New
4-8 Digit User
2 blinks +
Code
2 beeps
Add another code
Same 4-8 Digit
User Code
2 blinks +
2 beeps
Delete another
code
Same New
6 Digit
2 blinks +
Programming
2 beeps
Code
or
1 blink +
1 beep
or
2 blinks +
2 beeps
Enable:1 blink + 1 beep
Disable: 2 blinks + 2 beeps
2 blinks +
2 beeps
Enable:1 blink + 1 beep
Disable: 2 blinks + 2 beeps
Same Desired
User Code
2 blinks +
Length
2 beeps
Enable:1 blink + 1 beep
Disable: 2 blinks + 2 beeps
1 blink +
thumbturn.
1 beep
2 blinks +
2 beeps
OR
The lock was
not included/
excluded
© Allegion 2014
Printed in USA
P516-872 Rev. 03/14-a
Publicité
