General Tv Operation; Troubleshooting & Tips - Salora 32LED8100C Mode D'emploi

General TV Operation

Using the Channel List
The TV sorts all stored stations in the Channel List. You can
edit this channel list, set favourites or set active stations to
be listed by using the Channel List options.
Configuring Parental Settings
To prohibit viewing of certain programmes, channels and
menus can be locked by using the parental control system.
To display parental lock menu options, the PIN number
should be entered. The factory default PIN number is 0000.
After coding the correct PIN number, parental settings menu
will be displayed.
Menu Lock: Menu lock setting enables or disables the
menu access.
Maturity Lock: When set, this option gets the maturity
information from the broadcast and if this maturity level is
disabled, disables access to the broadcast.
Child Lock: When Child Lock is set, the TV can only be
controlled by the remote control. In this case the control panel
buttons will not work.
Set PIN: Defines a new PIN number.
Note: If the Country option is set to France, you can use 4725
as the default code.
Electronic Programme Guide (EPG)
Some, but not all channels send information about the current and
next programmes. Press the
Up/Down/Left/Right: Navigate EPG.
OK: Displays programme options.
INFO: Displays, in detailed, information on the programme selected.
GREEN: Switches to List Schedule EPG.
YELLOW: Switches to Timeline Schedule EPG.
BLUE: Displays filtering options.
Programme Options
In EPG menu, press the OK button to enter the Event
Options menu.
Select Channel
In EPG menu, using this option, you can switch to the
selected channel.
Set Timer / Delete Timer
After you have selected a programme in the EPG menu, press
the OK button. Select the Set Timer on Event option and press
the OK button. You can set a timer for future programmes. To
cancel an already set timer, highlight that programme and press
the OK button. Then select "Delete Timer" option. The timer
will be cancelled.
Note: It is not possible to record two channels at the same time.
Software Upgrade
Your TV is capable of finding and updating automatically via the
Aerial/Cable signal or over the Internet.
Software upgrade search via user interface
Simply navigate on your main menu. Choose Settings
and select Other Settings menu. In Other Settings
menu navigate on to the Software for Upgrade item and
"EPG"
button to view the EPG menu.
press OK button to check for a new software upgrade.
Note : Internet connection is needed. If an internet connection
is not available, try to upgrade via broadcast. If a new upgrade
is found, it starts to download the upgrade. Press OK to
continue with the reboot operation.
3 AM search and upgrade mode
While the TV is connected to an aerial signal. If Automatic
scanning in the Upgrade Options menu is enabled, the TV
wakes up at 03:00 and searches broadcast channels for new
software upgrades. If new software is found and downloaded
successfully, the next time the TV powers up , it will have the
new software version.
Note: If the TV fails to come on after the upgrade unplug the TV
for 2 minutes and plug in again.
Troubleshooting & Tips
Tv will not turn on
Make sure the power cord is plugged in securely to wall outlet.
The batteries in the remote control may be exhausted. Press the
Power button on the TV.
Poor picture
• Have you selected the correct TV system?
• Low signal level can cause picture distortion.Please check
antenna access.
• Check if you have entered the correct channel frequency if
you have done manual tuning.
• The picture quality may degrade when two devices are
connected to the TV at the same time. In such a case,
disconnect one of the devices.
No picture
• No Picture means that your TV is not receiving a transmission.
Have you selected the correct button on the remote control?
Try once more. Also make sure the correct input source has
been selected.
• Is the antenna connected properly?
• Is the antenna cable damaged?
• Are suitable plugs used to connect the antenna?
• If you are in doubt, consult your dealer.
No sound
• Has the TV been set to mute? To cancel mute, press the "
or increase the volume level.
• Sound is coming from only one speaker. Is the balance set
to one extreme? See Sound Menu section.
Remote control - does not operate
• The batteries may be exhausted. Replace the
bateries.
Input sources - can not be selected
• If you cannot select an input source, it is possible that no
device is connected. if not
• Check the AV cables and connections if you have tried to
connect a device.
English - 24 -
" button,