Bosch GAS 35 L SFC+ Professional Notice Originale page 19

OBJ_BUCH-1702-001.book Page 19 Thursday, February 14, 2013 4:05 PM
Mounting VAC Accessories
The vacuum hose 21 and the SFC+ module 20 are equipped
with a clip system, with which the VAC accessories (tool
sleeve 19, elbow 22) can be connected.
Mounting the Tool Sleeve (see figure C)
– Mount the SFC+ module 20 onto the vacuum hose 21 until
both snap-fasteners 31 of the vacuum hose can be heard
to engage.
– Afterwards, mount the tool sleeve 19 onto the SFC+ mod-
ule 20 until both snap-fasteners 31 of the SFC+ module
can be heard to engage.
– To disassemble, press both snap-fasteners 31 inward and
pull the components apart.
Mounting Nozzles and Tubes (see figure D)
– Mount the elbow 22 onto the vacuum hose 21 until both
snap-fasteners 31 of the vacuum hose can be heard to en-
gage.
– Afterwards, mount the desired VAC accessory (floor noz-
zle, crevice nozzle, vacuum tube, etc.) firmly onto the el-
bow 22.
– To disassemble, press both snap-fasteners 31 inward and
pull the components apart.
Inserting/Removing a Disposal Bag or Dust
Bag (Dry Vacuuming) (see figures E1
For dry vacuuming, a disposal bag 23 or a dust bag (accesso-
ry) can be used. This makes the disposal of the dust easier.
Note: When using a paper filter bag, the semi-automatic filter
cleaning (SFC+) (see "Deactivating the SFC+", page 20),
must, and when using a fleece filter bag, should be shut off.
Inserting a Disposal bBag
– Unlock the latches 9 and remove the vacuum lid 8.
– Insert the disposal bag 23 into the container 1 with the fill-
ing opening toward the front.
– Pull the filling opening over the connection flange into the
recess of the connection flange.
– Make sure that the disposal bag 23 faces completely
against the interior sides of the container 1.
– Fold the rest of the disposal bag 23 over the edge of the
container 1.
– Reattach the vacuum lid 8 again and lock the latches 9.
Removing and Closing the Disposal Bag
– Unlock the latches 9 and remove the vacuum lid 8.
– Pull the full disposal bag 23 toward the rear off of the con-
nection flange.
– Carefully remove the disposal bag 23 out of the vacuum
cleaner without damaging it.
When doing this, pay attention that the disposal bag does
not get caught or ripped open against the connection
flange or other sharp objects.
– Pull the cover off of the adhesive strip, close the disposal
bag and tape it shut.
Afterwards, tie off the disposal bag 23 below the filling
opening with the pulled off cover of the adhesive strip.
Bosch Power Tools
Replacing/Inserting the Dust Bag (Accessory)
– Unlock the latches 9 and remove the vacuum lid 8.
– Pull off the full dust bag from the connection flange toward
the rear. Close the opening of the dust bag by folding down
the lid. Remove the closed dust bag from the vacuum
cleaner.
– Work the new dust bag over the connection flange of the
vacuum cleaner. Make sure that the dust bag faces com-
pletely against the interior sides of the container 1 over its
full length.
– Reattach the vacuum lid 8 again and lock the latches 9.
Inserting the Rubber Lip (Wet Vacuuming)
(see figure F)
Note: The requirements for the ingress degree (dust
category L) have only been proven for dry vacuuming.
– Carefully pry the brush inserts 27 out of the floor nozzle 28
using a suitable tool.
– Insert the rubber lips 26 into the floor nozzle 28.
Note: The structured side of the rubber lips must face out-
ward.
Attaching an L-Boxx (see figure G)
For transport of the vacuum cleaner and for place-saving stor-
age of VAC accessories and/or power tools, an L-Boxx can be
E2)
–
mounted on the vacuum cleaner lid.
– Mount the L-Boxx onto the retainers 7.
 Do not carry the vacuum cleaner by the carrying handle
of the mounted L-Boxx. The vacuum cleaner is too heavy
for the carrying handle of the L-Boxx. Danger of injury and
causing damage.
Operation
Starting Operation
 Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the vacuum cleaner. Equipment marked
with 230 V can also be operated with 220 V.
 Please inform yourself about the valid regula-
tions/laws for your country concerning the handling of
materials that are hazardous to one's health.
The vacuum cleaner is suitable for vacuuming and extracting
the following materials:
– Dusts with an exposition limit value > 1 mg/m
The vacuum cleaner may generally not be used in rooms
where the danger of an explosion exists.
To save energy, only switch the vacuum cleaner on when us-
ing it.
To ensure optimal vacuuming performance, always complete-
ly unwind the vacuum hose 21 from the vacuum cleaner lid 8.
Dry Vacuuming
Vacuuming of deposited dusts
– To switch the vacuum cleaner on, set the mode
selector switch 5 to the "vacuuming" symbol.
English | 19
3
1 619 929 L27 | (14.2.13)