Thermor EVIDENCE 3 PLUS Mode D'emploi page 15

LOCK APPLIANCE CONTROL BOX
To avoid manipulations by children, you can lock
appliance control box pressing buttons
the same time. Hold buttons around 3 seconds.
The screen shows
locked.
Make same operation to unlock the appliance
control box. The screen shows
APPLIANCE SETTINGS
Press the button
pictogram lights up. The settings menu contains:
– SETTING THE TIME AND DAY OF THE WEEK
Using buttons and
Set the hour . Set the minute
the week (1 – Monday, 2 – Tuesday...).
Note: after appliance switch Off / On, it may be
necessary to re-set the time and day of the
week.
– ACTIVATION / DEACTIVATION THE OPEN
WINDOW DETECTION
Allows to detect the temperature change caused
by opening and closing the window. If you forget to
switch off the appliance before long-term ventilation
of the room, this function prevents unnecessary
heating.
Using buttons and
Activate / deactivate function of the open window
detection ( /
If appliance detects that window is opened, the
parameter flashes on the screen and appliance
switches automatically to frost protection mode
(7°C).
If appliance detects that window is closed or the
cycle is stopped manually, the parameter
disappear from the screen and appliance will return
to the previous operating mode.
To manually stop the open window detection
cycle:
- Using buttons and
- Confirm using button
Note: it is not recommended to use this function
in rooms with a draught, for example in
corridors or in rooms near the front door.
– PROGRAM FOR EACH DAY OF THE WEEK
7 programs are preset. By default, programs are
already assigned for each day.
Comfort
P1
Eco
0h
Comfort
P2
Eco
0h
Comfort
P3
Eco
0h
Comfort
P4
Eco
0h
Comfort
P5
Eco
0h
Comfort
P6
Eco
0h
Comfort
P7
Eco
0h
0h
It is possible to change the program for the day you
want. Using buttons
. Select a day for programming e.g., Monday
. Select program from P1 to P7 for selected day.
Repeat these steps to select the program for each
day of the week.
and
. Appliance control box is
.
until the indicator below the
, select parameter
. Set the day of
, select parameter
).
, select parameter
.
6h 18h
9h
6h
9h
18h
6h 12h 18h
9h 14h
6h
8h 18h
12h
6h 12h 18h
and , select parameter
EN
– PROGRAMS CHANGE
It is possible to change the preset programs. For
at each program (from P1 to P7) it is possible to select
operating mode hourly (from 0 to 23 hours). Using
buttons and
the program for changing
operating mode for each hour
Repeat these steps to change all programs.
APPLIANCE SETTINGS MENU
Exit the settings
.
.
will
Exit the settings
EXPERT MENU
To access the advanced functions of the
device, press and hold 2 buttons around 3
seconds.
;
– CALIBRATION
It is possible to adjust the temperature measured
by the appliance according to the room temperature.
The calibration value is from -3°C to +3°C comparing
to the temperature shown on the screen.
– MAXIMUM TEMPERATURE
It is possible to change the temperature, which
cannot be exceeded (from 19°C to 28°C). By default,
21h
the maximum temperature is 28°C.
– HEATING INDICATOR
It is possible to switch off the heating indicator,
21h
when appliance is in standby mode. To switch off the
21h
indicator, choose parameter «oF».
21h
– SCREEN
It is possible to choose which temperature to show
21h
on the screen before switching to standby mode:
- «St» to show the set temperature.
24h
- «Pt» to show the measured temperature.
– FACTORY SETTINGS
It is possible to reset appliance to factory settings.
Choose parameter
temperature set-point 19°C, Programming by default.
15
, select parameter
/ . Select the
/ /
«Go». Comfort
. Select
.
mode,