Rubi TC180 Traduction De La Notice Originale page 13

7. If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce dust-
related hazards.
POWER TOOL USE AND CARE
1. Do not force the power tool. Use the cor-
rect power tool for your application. The
correct power tool will do the job better and
safer at the rate for which it was designed.
2. Do not use the power tool if the switch
does not turn it on and off. Any power tool
that cannot be controlled with the switch is dan-
gerous and must be repaired.
3. Disconnect the plug from the power source
and/or the battery pack from the power
tool before making any adjustments,
changing accessories, or storing power
tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
4. Store idle power tools out of the reach of
children and do not allow persons unfamil-
iar with the power tool or these instruc-
tions to operate the power tool. Power tools
are dangerous in the hands of untrained users.
5. Maintain power tools. Check for misalign-
ment or binding of moving parts, breakage
of parts and any other condition that may
affect the power tool's operation. If dam-
aged, have the power tool repaired before
use. Many accidents are caused by poorly main-
tained power tools.
6. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
7. Use the power tool, accessories and tool
bits etc., in accordance with these instruc-
tions, taking into account the working con-
ditions and the work to be performed. Use
of the power tool for operations different from
those intended could result in a hazardous situ-
ation.
SERVICE
1. Have your power tool serviced by a quali-
fied repair person using only identical re-
placement parts. This will ensure that the
safety of the power tool is maintained.
SAFETY INSTRUCTIONS FOR CUTTING-
OFF OPERATIONS
CUT-OFF MACHINE SAFETY WARNINGS
ENGLISH
ORIGINAL INSTRUCTIONS
1.
2.
3.
4.
5.
6.
7.
8.
9.
The guard provided with the tool must be
securely attached to the power tool and po-
sitioned for maximum safety, so the least
amount of blade is exposed towards the
operator. Position yourself and bystanders
away from the plane of the rotating blade.
The guard helps to protect operator from broken
blade fragments and accidental contact with blade.
Use only diamond cut-off blades for your
power tool. Just because an accessory can be
attached to your power tool, it does not assure
safe operation.
The rated speed of the accessory must
be at least equal to the maximum speed
marked on the power tool. Accessories run-
ning faster than their rated speed can break and
fly apart.
Blades must be used only for recommend-
ed applications. For example: do not grind
with the side of cut-off blade. Abrasive cut-off
blades are intended for peripheral grinding, side
forces applied to these blades may cause them to
shatter.
Always use undamaged blade flanges that
are of correct diameter for your selected
blade. Proper blade flanges support the blade
thus reducing the possibility of blade breakage.
The outside diameter and the thickness of
your accessory must be within the capacity
rating of your power tool. Incorrectly sized
accessories cannot be adequately guarded or con-
trolled.
The arbour size of blades and flanges must
properly fit the spindle of the power tool.
Blades and flanges with arbour holes that do not
match the mounting hardware of the power tool
will run out of balance, vibrate excessively and
may cause loss of control.
Do not use damaged blades. Before each
use, inspect the blades for chips and cracks.
If power tool or blade is dropped, inspect
for damage or install an undamaged blade.
After inspecting and installing the blade,
position yourself and bystanders away from
the plane of the rotating blade and run the
power tool at maximum no load speed
for one minute. Damaged blades will normally
break apart during this test time.
Wear personal protective equipment.
Depending on application, use face shield,
safety goggles or safety glasses. As appro-
priate, wear dust mask, hearing protectors,
gloves and shop apron capable of stopping
small abrasive or workpiece fragments. The
eye protection must be capable of stopping flying
13