Installation; Commissioning; Operation - Lux Tools HD-170/2500 Notice Originale

Hochdruckreiniger_345707.book Seite 26 Freitag, 25. November 2016 2:54 14
GB
4. Cleaning agent tank
5. Cable holder
6. On/Off switch
7. Water connection
8. Holder for spray gun
Scope of delivery
► P. 3, item 2
• High-pressure cleaner
9. Terrace cleaner
10. Hand-held spray gun
11. Jet pipe with rotary nozzle for high pressure

operation

12. Jet pipe with fan-type jet nozzles for low pres-
sure and high pressure operation (depending on
the setting of the nozzle head)
13. Connecting pipe
14. Wash brush
• Holder for spray gun
• Cable holder
• Handle
• Plug-in coupling for water connection
• Cleaning needle for high-pressure nozzle
• Instructions for use

Installation

► P. 4, item 3
– Attach the holder for the spray gun (8).
► P. 4, item 4
– Insert the jet pipe with the fan-type jet nozzle (11)
or the jet pipe with the rotary nozzle (12) into the
spray gun (10) and rotate by approx. 90° until the
two parts are securely connected.
– Insert the terrace cleaner (9) into connecting
pipe (13) and rotate approx. by 90° until the two
parts are securely connected.
► P. 4, item 5
1. Insert the connecting pipe (13) into the spray
gun (10) and rotate by approx. 90° until the two
parts are securely connected.
2. Tighten the counter nut (15).
► P. 4, item 6
– Insert the pressure hose (1) into the hand-held
spray gun (10) in such a way that it engages
audibly.
► P. 4, item 7
– To separate the pressure hose (1) and hand-held
spray gun (10), press the unlocking button (16).
► P. 5, item 8
– Screw the supplied plug-in coupling (17) onto
the water connection of the product by hand.

Commissioning

Water supply
NOTICE! Risk of environmental dam-
age! In accordance with EN 61770, the
product must not be directly connected to
the public drinking water supply.
Always use a system separator in accord-
ance with EN 12729 type BA.
26
Note: Observe the regulations of your
water supply company.
The following accessories are required for connect-
ing the machine (not included):
• a fabric-reinforced hose with a minimum diame-
ter of 13 mm (½")
– Insert the water hose into the plug-in coupling
and connect to the water supply.
Mains supply
– Ensure that the on/off switch (6) is at [0].
– Open the water inlet.
– Insert the mains plug into the socket.
Operation
Check before switching on!
Check the safe condition of the machine:
– Check it for visual defects.
– Check that all parts of the machine have been
securely fitted.
– Check if the water connector and the high-pres-
sure pipes are tight.
Water inlet
– Open the water inlet.
► P. 5, item 9
– Retract the switch-on safety lock (18).
– Actuate the lever (19) of the spray gun until a
water jet escapes continually.
NOTICE! Risk of machine damage!
Never operate the machine without water
inlet as dry running may damage the pump.
Use a water filter if the inlet water is con-
taminated.
Switching on/off
– To switch the machine on, set the On/Off
switch (6) to [I].
– To switch the machine off, set the On/Off
switch (6) to [0].
Switching on the water jet
DANGER! Risk of fatal injury! Use special
care when cleaning tyres. Vehicle tyres/tyre
valves may become damaged or burst
when handled improperly. First signs of
damage included discolourations on the
tyre. Damaged vehicle tyres/tyre valves
pose a life-threatening risk. Keep the jet at
a distance of at least 30 cm!
DANGER! Risk of fatal injury! The high-
pressure jet may be dangerous when han-
dled improperly. The jet may not be
directed towards living beings (persons,
animals), live equipment or the machine
itself.
– Hold the hand-held spray gun and the jet tube
firmly with both hands. Be aware of the recoil
when switching on the high-pressure jet.