Unpacking The Device; Assembly Instructions; Base Unit (Fig. A - C); Fan (Fig. D) - AEG VL 5569 LB Mode D'emploi

unpacking the Device

• Remove the device from its packaging.
• Remove all of the packaging material such as foils,
filling material, cable holders and cardboard packaging.
• Check the scope of delivery.
NOTE:
There may still be dust or production residues on the sur-
face of the device. We recommend that you quickly wipe of
the housing with a damp cloth.

Assembly instructions

The appliance must be fully assembled before use! We
recommend that you refer to the figures "Overview" and
"Assembly overview" when assembling.
Base unit (Fig. a – c)
1. Screw the tubes (7) onto the stand (13). Use the four
screws (12), the metal plate (14), and the four nuts (15).
2. Attach the cover of the stand (16) to the stand tubes.
NOTE:
The nuts and screws (17) are preinstalled on the rear of the
switch housing.
3. Check if the screws (17) possibly have been screwed into
deeply. In this case, turn the screws back a little. Do not
screw them out all the way!
NOTE:
If a screw or a bolt should have dropped off, proceed
as follows:
• Hold the preassembled unit (motor (18), switch
housing (6), and humidifier base (10)) so that the
motor points down.
• Insert one nut (M6) each into the shaft at the side of
the recesses for the tubes.
• Screw the two screws (17) on the rear of the switch
housing lightly into the nuts.
4. Set the preassembled unit for a depth of approximately 3
cm onto the stand tubes.
NOTE:
The humidifier cable must be routed between the two
tubes.
Secure the preassembled unit to the stand tubes by
tightening the two screws (17).
5. Fasten the base of the humidifier (10)
with the large screw (ST4*25mm) to the
base of the stand. For this, insert the
screw from below through the stand and
its cover into the small outer bore (Fig.
on the right).
All manuals and user guides at all-guides.com

Fan (Fig. d)

6. Remove the preinstalled nut (20) from the motor (18).
7. Align the rear protection grid (19) with the motor recesses
8. Tighten the nut (20) for the rear protection grid clockwise.
9. Attach the propeller (3). When doing so, use the guide
10. Tighten the screw (21) for the propeller anti-clockwise.
11. Remove the prefitted screw and nut (5) from the front
12. Open the fastening hooks (2) at the front protection grid.
13. Attach the front protection grid by engaging the groove
14. Secure the protection grid with the screw and the nut (5).
15. Close the four fastening hooks (2).
Humidifier (Fig. e – f)
The tube already may have been installed on the switch
housing. In this case, continue the assembly from item 18.
16. Feed the tube (8) from front to back between the two
17. Insert the tube from the back to the front through the
18. Pull the tube tight so that it lies flat against the back of
19. Connect the top end of the tube to the tube connector
20. Place the water tank (9) onto the base of the humidifier
21. Fit the tank cap on the bottom end of the tube onto the
Keep it close to hand.
(18).
NOTE:
The handle must point upwards.
pin on the motor shaft.
protection grid (22). Keep it close to hand.
of the hook (1) with the rear protection grid.
NOTE:
The holes for the screw (5) in the front and rear protec-
tion grid must be aligned.
stand tubes (7). Then insert the tube from the bottom
upwards through the opening on the underside of the
switch housing (6).
NOTE:
The end of the tube with the tank cap must be positi-
oned at the front above the humidifier.
opening on the top of the switch housing.
the switch housing.
NOTE:
The two ends of the tube should have approximately
the same length.
on the protection grid (22).
NOTE:
The tube above the switch housing must not "sag".
Water which accumulates in the tube prevents the
formation of the mist. If necessary, push back the top
section of the tube.
(10).
water tank. The recess on the tank cap must fit into the
groove on the opening to the water tank.
English
41