Aikan MAX205BAR Mode D'emploi page 6

ENG
power to "on" (16)
►
suction tube to the unit to priming tube until paint
discharges from priming tube
"off" (9) Remove the priming tube from the waste
►
bucket and clip to suction tube and submerge in
paint pail (19) Switch power to "on" (16)
►
airless gun into waste bucket and pull trigger (11)
Turn "spray/prime" switch to "spray" mode and
►
continue to spray into waste bucket (20)
spraying If the motor stops, means that the pump
and tubes are primed
priming steps Start painting.
►
PAINT.
Before painting, ensure the the unit has been
►
primed and verify that nozzle tip is aligned properly
Remove or cover objects that you want to protect
►
from overspray and paint mist
adjust nozzle to "spray" setting (3)
at the lowest setting on the pressure control knob
and increase pressure as needed by turning
clockwise to create a good spray pattern (21)
Practice the painting techniques that follow on a
►
scrap workpiece before painting your workpiece.
PAINTING TECHNIQUES.
Before painting, ensure the the unit has been
►
primed and verify that nozzle tip is aligned properly
Keep the airless gun approximately 30 cm from
►
the surface Keep airless gun straight and move
►
arm across at a steady rate while staying 30 cm
from the surface (22)
or paint will be uneven (23)
by half, always aim stroke at bottom edge of last
stroke (24).
CLEARING AIRLESS GUN TIP.
Occasionally, the airless gun tip will become
►
clogged with paint
►
clear airless gun tip
►
Adjust nozzle to "clean/eject" setting (4)
►
"spray/prime" switch to "spray" mode (20)
power to "on" (16)
►
clog clears (11) Release trigger
►
to "spray" mode (3).
CLEANING.
Turn power off and turn "prime/spray" switch
►
to "prime" mode to relieve pressure (10)
Unthread airless gun tip and remove (25) (26)
►
Relieve pressure and drain paint from tubes
►
(27) Separate tubes (12)
►
in empty waste bucket (13)
tube in water or flushing fluid (14)
Paint should work itself from
Switch power to
►
►
If it does not stop, repeat
►
Once primed,
►
Start spraying
►
Do not fan the airless gun
►
Overlap strokes
►
Follow these instructions to
Switch power to "off" (9)
Spray into waste bucket until
Adjust nozzle
►
Place priming tube
►
Submerge suction
►
Plug in the
►
unit and turn "on" power (16)
start pumping and water or flushing solvent as
well as air bubbles will be purged from system
Let fluids discharge from priming tube into
►
waste bucket until fluid is clear (28)
Point in priming tube is clear, switch power to "off" (9)
►
Turn "spray/prime" switch to "spray" mode (20)
►
Switch power to "on" (16)
►
Stop (29) Change to waste bucket as paint thins
►
(30) Turn "prime/ spray" switch to "prime" mode
►
(10) Continue to flush until clear (31)
►
trigger, turn power "off" and relieve pressure (9,
10, 11)
(32) Unscrew nut from housing, it is behind
►
the swivel connector (33)
Clean all parts in warm, soapy water or flushing
►
fluid with a bristled brush (35).
STORAGE.
When cleaning for long term storage (more
►
than 48 hours). it is important that the unit is not
stored with any water or water-based material left
in the pump, hose, tubes, or airless gun
will corrode the product
the the unit before storage
if not already removed (36)
and loosen the clamps from both tubes, then
disconnect tubes from the pump body (37)
about 30 mililitres of light household oil or a pump
storage product into each inlet (38)
spray" switch to "spray" (20)
control knob to "low pressure spray" (8)
rag over the paint hose outlet (39)
to "on" for five seconds, then turn the power to "off"
(40) Turn "prime/spray" switch to "prime", this will
►
keep storage fluids in the unit (10)
tubes and secure with the clamps (41)
the unit with a clean cloth
location out of reach of children.
MAINTENANCE.
Turn
►
Turn The airless electric equipment has been
► ►
designed for a long working life with minimum
maintenance
correct care of the airless electric equipment and
regular cleaning
unplug the airless electric equipment from the
power source before cleaning or performing any
maintenance
may be cleaned effectively using compressed
air after each use
available, use a brush to remove dust from the
airless electric equipment
vents and switch levers must be dept clean and
6
English
►
Remove the trigger guard from housing
►
Remove filter (34)
►
Is very important clean
►
►
►
Store in a clean dry
►
Optimum use depends on
►
To prevent accidents, always
►
The airless electric equipment
►
If compressed air is not
►
Motor ventilation
►
The unit will
►
After fluid
►
Paint into paint pail
Release
►
This
►
Remove paint hose
Turn the unit over
Add
►
Turn "prime/
►
Turn pressure
►
Hold a
►
Switch power
►
Replace the
►
Wipe the
►