Aikan MAX205BAR Mode D'emploi page 5

ENG
1
2
4
3
5
1. Carry handle.
2. Suction hose.
3. Return hose.
4. On/off switch.
5. Inlet filter.
6. Inlet valve pusher.
7. Pressure regulator.
8. Prime/spray selector.
9. Airless gun.
10. Airless hose.
11. Hose connection.
USE INSTRUCTIONS.
Before starting up the airless electric equipment,
►
we recommend that you carefully read all of the
instructions as indicated
regulations regarding the prevention of accidents,
health and safety directives, laws and applicable
restrictions for work places
equipment must only be used by persons who have
been instructed in its use and only for the purposes
for which it has been designed.
POWER SUPPLY.
Make sure the power supply is adapted to the
►
requirements shown on the information panel of the
airless electric equipment (1)
low voltage will make it operate slowly
reduce performance and may cause the motor to
overheat.
EXTENSION CORD.
If the working area is at some distance from the
►
power supply, use an extension cord of enough
diameter and quality.
EARTH CONNECTION.
The airless electric equipment must be
►
connected to earth while being used to protect the
operator from possible electrical shocks.
PRIME/SPRAY
This switch toggles the unit between the
►
"priming" and "spraying" mode (2).
8
11
6 7
Please respect all
►
The airless electric
►
Using the motor at
►
This will
►
NOZZLE.
The nozzle is reversible and removable to make
►
cleaning and unclogging easier
position to use the airless gun (3)
opposed position to clean the nozzle (4).
9
PRESSURE CONTROL KNOB.
The pressure control knob can be adjusted for
►
10
high pressure spraying, low pressure spraying,
priming/cleaning and rolling
align the pressure control knob with indicator on
the housing (5).
INSTALATION.
Remove or cover objects that you want to
►
protect from overspray (paint mist)
hose to paint hose outlet and tighten with wrench
(6)
Attach paint hose to airless gun and tighten
►
with two wrenches (7)
knob to "low pressure spray" setting (8).
RELIEVE PRESSURE.
Turn power switch "off" and unplug unit from
►
outlet (9)
►
mode to safely release most pressure (10)
airless gun into paint pail and activate the airless
gun trigger to relieve an remaining pressure (11)
Note: Always set to "prime" mode between uses.
►
PRIME AIRLESS GUN.
This procedure is used for first time operation
►
and also to flush storage fluids out of the airless
gun For oil-based paint, flush with mineral
►
spirits followed by warm clean water
to prevent fire: When using mineral spirits, ground
airless gun by holding it against a metal container
while flushing
flush with warm clean water.
PRIME AND STARTUP.
Separate smaller priming tube from suction
►
tube (12)
►
(13) Submerge suction tube in water or flushing
►
solvent (14)
mode (10)
"prime/clean" setting (15)
turn "on" power (16)
and water or flushing solvent as well as air
bubbles will be purged from system
discharge from priming tube into waste bucket
for 30 to 60 seconds then switch power to "off"
(9) Important: If solvent will not flow through
►
hoses, try pressing the red inlet release button
underneath the pump to loosen the inlet check ball
(17) Remove suction tube from water or flushing
►
solvent and submerge in paint pail (18)
5
English
To set the function,
►
Turn pressure control
►
Turn "prime/spray" switch to "prime"
For water-based (latex) paint,
►
Place priming tube in waste bucket
Turn "prime/spray" switch to "prime"
►
Adjust pressure control knob to
►
Plug in the unit and
►
The unit will start pumping
►
Turn to "spray"
►
Turn to the
►
Attach paint
►
Point
►
Warning!
►
Let fluids
►
Switch
►