Publicité
Les langues disponibles
Les langues disponibles
4. Connect fixture black wire to house black wire and
fixture white wire to house white wire by firmly
pushing into quick connect wiring connectors
(Fig. 6).
5. Connect house ground wire and fixture ground wire
by firmly pushing into quick connect wiring
connector. (Fig. 6). Attach fixture (A) to the mounting
bracket (B) using (2) #8 x 1-1/4 in. screws (F)
pre-attached to the canopy. Be sure no loose wires
remain sticking out from underneath the coverplate.
Insert the decorative screw cover caps (G) into the
screw holes on the coverplate for a finished appear-
ance (Fig. 6).
6. Adjust light fixture to desired postion by loosening the lower arm jam nut and the
thumbscrew on the upper arm. Move the head to aim and retighten the thumbscrew and
jam nut.
7. Apply silicone caulk around the edges of the coverplate and jam nuts at the base of the
adjustment arms to provide a watertight seal from rain and moisture.
8. Turn on power at main fuse/breaker box.
6
A
OPERATING YOUR FIXTURE
1. Set dial to "TEST" (Fig. 4).
2. Turn the arrow on the SENSITIVITY knob to a
middle point between "+" and "–".
3. Turn on the power to fixture. Allow fixture to warm
up approximately 40 seconds before testing.
4. Aim sensor head toward desired detection area,
maintaining a 5° down angle to allow moisture
to drain.
NOTE: Maintain air spacing between lamps and sensor
head, at least 2 in. Make sure sensor head is positioned
with control switches facing towards the ground.
5. Walk through the detection zone at the farthest
distance you want your detector to detect motion.
6. Adjust the SENSITIVITY knob until you get desired results. For more range, aim sensor
slightly upward. For less range, aim sensor head slightly downward. Lights will turn
OFF 4 seconds after motion stops.
7. Set dial to desired time setting. The higher the time setting, the longer the lamps will be
ON. (Maximum time is 12 minutes.)
NOTE: Decreasing the SENSITIVITY will decrease the distance the unit can detect.
SELECTING YOUR DESIRED FEATURE
Mode of
Operation
Auto Setting (motion activated)
Lights should turn ON with
motion only at night and should
turn OFF according to the
TIME dial setting.
Dusk to Dawn Setting
(activated only at night)
Lights should turn ON for 6 hours
at dusk and then reset to
the Auto Setting.
Test Setting
Lights should turn ON with
motion both day and night.
Lights should turn OFF
after 4 seconds.
Return to Auto Setting
(motion activated)
From any of the above settings
5
C
Quick Connect
wiring connector
G
Fig. 4
MODE Knob
How to Set
Adjustment
Power Switch
Knob arrow points to
Turn the power
desired time setting
to the fixture ON.
within TIME range.
Knob arrow points to
Turn the power
desired time setting
OFF and ON twice
within TIME range.
within 3 seconds.
TEST
Turn the power
to the fixture ON.
Knob arrow points to
Turn the power OFF
desired time setting
for at least 40 seconds
within TIME range.
and then back ON.
TROUBLESHOOTING
Light does not
No power to the fixture.
come on with
E
motion at night.
Bulb is faulty.
Surrounding external
ambient light is too
A
bright. (If so, the unit
may think it is daytime.)
Wiring to the unit
is loose.
Light comes on
There is motion in the
for no apparent
detection zone.
reason at night.
Junction
box
B
Light stays
There is motion in the
on at night
detection zone.
and does not
turn off.
Unit is in Dusk-to-Dawn
mode (if there is
no motion).
Light
The light given from
continuously
the unit's own lamp
blinks on and
is affecting the
off at night.
motion sensor.
Light is on
The controls on
during the day.
the bottom of the
motion sensor are
in "TEST" mode.
The motion detector
is shadowed.
Cannot activate
Surrounding external
Dusk-to-Dawn
ambient light is too
mode at night
bright. (If so, the unit
(override).
may think it is daytime.)
Not enough time is
allowed to enter the
Dusk-to-Dawn mode.
5-YEAR IMITED WARRANTY
THE FOLLOWING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES,
WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING, BUT NOT LIMITED TO, ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
Eaton warrants to customers that, for a period of five years from the date of purchase, Eaton
products will be free from defects in materials and workmanship. The obligation of Eaton
under this warranty is expressly limited to the provision of replacement products. This war-
ranty is extended only to the original purchaser of the product. A purchaser's receipt or other
proof of date of original purchase acceptable to Eaton. This is required before warranty per-
formance shall be rendered. This warranty does not apply to Eaton products that have been
altered or repaired that have been subjected to neglect, abuse, misuse or accident (including
shipping damages). This warranty does not apply to products not manufactured by Eaton
which have been supplied, installed, and/or used in conjunction with Eaton products. Damage
to the product caused by replacement bulbs or corrosion or discoloration of brass components
are not covered by this warranty.
LIMITATION OF LIABILITY:
IN NO EVENT SHALL EATON BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUEN-
TIAL DAMAGES (REGARDLESS OF THE FORM OF ACTION, WHETHER IN CONTRACT, STRICT
LIABILITY, OR IN TORT INCLUDING NEGLIGENCE), NOR FOR LOST PROFITS; NOR SHALL THE
LIABILITY OF EATON FOR ANY CLAIMS OR DAMAGE ARISING OUT OF OR CONNECTED WITH
THESE TERMS OR THE MANUFACTURE, SALE, DELIVERY, USE, MAINTENANCE, REPAIR OR
2
• Check if circuit breaker tripped.
• Confirm wall switch is ON.
• Replace bulb.
• Re-aim the head.
• Relocate or reposition the unit away from
the light.
TURN OFF POWER BEFORE CONTINUING
• Check wiring; reconnect if necessary
using wire nuts (E) provided.
• Make sure the sensor is not picking
up moving objects such as trees,
traffic, etc.
TEST FOR YOURSELF.
• Cover the sensor lens with cardboard
to prevent sensor from detecting
motion. If the light stays off, something
in the detection zone is triggering the
sensor.
*If the light stays on with the sensor lens
covered, contact customer service.
• Reduce sensitivity.
• Reposition the sensor.
• Make sure the sensor is not picking up
moving objects such as trees, traffic, etc.
• Reduce sensitivity.
• Reposition the sensor.
• Turn the light switch to the OFF
position for 40 seconds, and then turn
back to the ON position. This will send
the unit back into the "Auto" mode.
• Re-aim the lamp.
• Reposition motion sensor.
• Change dial setting (not "TEST" mode).
• Reposition motion sensor.
• Re-aim the head.
• Relocate or reposition the unit away
from the light.
• Turn power OFF and ON twice within
3 seconds.
Publicité
