Carat T Serie Manuel D'utilisation page 11

- Any works on the electrical installations must be carried
out by qualified electricians¬.
- Annual check of the electric system according to
VDE0701.
CAUTION!
Risk of cut injuries!
Reaching into moving tools may lead to heavy injuries.
- Do not touch rotating diamond blades in any
circumstances.
- De-energize the machine before replacing the diamond
blade.
There are the following symbols and information signs on
the machine that refer to potential dangers:
Warning of rotating tool!
Running direction of the
saw blade
Wear gloves. Wear ear
protectors. The machine
meets EU guideline.
Observe the operating
manual. Wear protective
goggles
Laser class: II
Wavelength: 635 nm
Laser
Class 2
635 mm
Warning!
ATTENTION
DO NO T
Do not stare into beam!
STARE
INTO
BEAM
3. MACHINE DATA
3.1 Diamond blades
DANGER!
Risk of injury by defective or incorrectly mounted
diamond blades!
Wrong rotation direction and damaged diamond blades
may cause injuries of personnel!
Check diamond blades for broken off segments and
segment pieces, segment foot cracks, diamond blade
deformations or signs of wear before starting work.
Pay attention to the rotation direction arrows on the
diamond blades and guard!
20
DANGER!
Risk of injury by unchecked or unapproved tool!
Diamond blades or buzz saw blades that have not been
checked or approved may cause injuries of personnel!
Before starting work, check whether a proper diamond
blade is mounted.
Pay attention to the rotation direction arrows on the
diamond blade and guard!
NOTE!
All diamond blades used must be designed in
terms of their permissible max. cutting ¬speed¬ to match
the max. drive speed and intended application of the
machine tool
Cutting wheel Diameter Material
Carat concrete T-3510 Concrete, washed
diamond blade Ø350 mm concrete, bricks
T-4010
Carat universal Concrete, washed
Ø400 mm
diamond blade concrete, bricks,
T-5010 clinker, hard stone,
Ø500 mm
granite
T-6010
Carat tiles and Hard stone, granite,
Ø600 mm
natural stone natural and artificial
diamond blade stone, hard clinker
T-7010
Ø700 mm
3.2 Type plate
The type plate is located on the base frame of the machine
tool.
3.3 Installation site requirements
The floor surface must:
- Have sufficient load bearing capacity.
- Be slip proof.
- Be level.
3.4 Storage requirements
Storage conditions
As a matter of principle, the machine, its components,
assemblies or parts must be only stored in the following
conditions: do not store outdoors. store in dry and dust-
free place. do not expose to aggressive media. protect
from solar radiation. avoid mechanical vibrations. storage
temperature range 5 to 45°C
relative air humidity, max. 60%. In case of storage for
over 3 months, check general condition of all parts and
packaging on a regular basis. If necessary, renew or replace
conservation materials.
4. TRANSPORT
ATTENTION!
Damage through improper transportation!
Improper transportation can result in considerable
damage of the machine and objects in the vicinity.
Before every transport:
- The cutter head must be locked.
- The cutter head must be lowered and locked.
- The cutting table must be secured by the table lock
(for table saw machines).
- The machine must be disconnected from power supply.
Due to two transport rollers, the machine can be
transported by one or two persons who can use transport
handles.
NOTE!
The machine is not designed for crane transport.
There are no appropriate load suspension points on the
machine.
5. INSTALLATION
5.1 Connection
Before connecting the machine to the power source,
make sure that:
- Voltage / phase of the power supply, match the date on
the type plate of the motor and machine.
- The power supply line is grounded according to the safety
provisions.
- T he wire size of the extension cord is sufficient, H07RNF
3x2.5 mm² up to 50m for 230V.
5.2 Mounting a diamond blade
To mount a new diamond blade or replace the used one,
proceed as follows:
1. S witch off the machine and interrupt the power supply
by pulling the mains cable from the mains outlet.
2. Loosen the screws on the diamond blade guard so as to
be able to remove the front half of the diamond blade
guard. For T-7010, after loosening the screw on back
of blade guard, disconnect the quick release of water
connector on top of blade guard, then remove the blade
guard.
3. L oosen the nut of the motor shaft and remove the outer
cutter flange.
4. Clean the cutter flange, nut and motor shaft.
5. Check the parts for signs of wear.
6. Mount or replace the diamond blade. While doing so,
pay attention to the correct rotation direction of the
diamond blade and motor shaft.
7. Replace the outer cutting flange on the motor shaft.
8. S crew the nut onto the motor shaft again and tighten it
firmly.
9. Replace the front half of the cutting wheel guard to
connect it with the rear half.
10. Tighten firmly the screws on the cutting wheel guard.
NOTE!
The arrow on the cutting wheel indicates
correct rotation direction.
NOTE!
The cutting wheel, irrespective of its position or
the position of the cutter head, may not touch the table!
5.3 Mounting the transport handles and wheels
Mount the transport handles at the appropriate places on
the base frame using the supplied washers (4x A8,4 ISO
7089) and the screws (4x M8x30 ISO 4017), the spring wash-
ers (4x A8 DIN 127) and the screws (4x M8x20 ISO 4017).
Do the same with the transport wheels. Mount the trans-
port wheels at the appropriate places on the base frame
using the supplied washers (4x A,8,4 ISO 7090), the spring
washers (4x A8 DIN127), the screws (4x M8x25 ISO 4017)
and the nuts (4x M8 ISO 4032).
Mounting the extension table
If you want to work with the extension table, proceed as
follows:
Insert the extension table into the lateral grommets on the
base frame and tighten it with the star grip screws
21