Publicité
Les langues disponibles
Les langues disponibles
Operations:
cleaning your HARD FLOORS
IMPORTANT CLEANING TIP:
Sweep area thoroughly before deep cleaning.
Before plugging in machine, check the POWER SWITCH to make sure it is in
CAUTION
the "off" position.
1
To Attach HARD FLOOR NOZZLE
1. Align the nozzle tabs with the slots in the base of
the machine.
3
2. Rotate NOZZLE
toward machine.
2
3. Latch the
NOZZLE by
pressing down
on the top of
the NOZZLE
1
until you hear a
"click."
3
Plug In The Machine
Unwrap the POWER CORD
and insert plug into a properly
grounded outlet.
5
Turn Machine On
Push the POWER SWITCH to
"FLOOR CLEANING" position.
7
Cleaning Your Hard Floors
Press the SOAP & SCRUB TRIGGER
to apply solution.
Make 2 slow wet passes
(1 forward, 1 back) over each area.
Release SOAP & SCRUB TRIGGER
approximately 6 inches from stop
point to ensure solution is removed.
12
F L E X C L E A N® A L L - I N - O N E F L O O R C L E A N E R
2
Select
Cleaning
Mode
Turn the FLOW
CONTROL DIAL to
the HARD FLOOR
setting.
4
Position The Machine
Position the machine onto the
desired area to clean.
6
Release The Handle
Step on the HANDLE RELEASE
PEDAL to pull back/release the
MAIN HANDLE.
8
Leave The Machine On
For 15 Seconds
Leave the machine on for 15 seconds
after cleaning to allow for all of the
Press
dirty solution to be collected into
Soap &
Spray
the DIRTY WATER TANK.
Trigger
|
U s e r M a n u a l
Operations:
THE UPHOLSTERY TOOL
Great to use on Upholstery, Stairs, Mattresses and Spot Cleaning.
CAUTION
1
Remove The Nozzle
If attached, remove the Nozzle from the machine:
1. Press the NOZZLE
RELEASE BUTTON
to unlock the NOZZLE.
2. Rotate the NOZZLE
away from the base of
the machine to remove.
3
Selecting Cleaning Mode
Turn the FLOW
CONTROL DIAL to
the DEEP CLEAN or
QUICK-DRY setting
based on desired
cleaning.
(Refer to "FLOW
CONTROL DIAL" instructions for
additional details if needed, Page 9).
6
Position The
Upholstery Tool
Handle
Position the
Release
UPHOLSTERY TOOL
Pedal
in front of the area or
stain you want to deep
clean.
8
Step 2 - How To Clean
Release the SPRAY TRIGGER
Move the tool back and forth over
the same area to suck up dirty water.
r u g d o c t o r . c o m
|
Before plugging in machine, check the POWER SWITCH to make sure it is in
the "off" position.
2
Attach The
Upholstery
Tool
Nozzle
Release
Insert the
UPHOLSTERY
TOOL CONNECTOR in the
UPHOLSTERY TOOL PORT,
located behind the NOZZLE.
4
Plug In The
Machine
Unwrap the
POWER CORD
and insert plug
into a properly
grounded
outlet.
7
Step 1 - How To Clean
Squeeze the SPRAY TRIGGER on
the UPHOLSTERY TOOL to begin
cleaning.
Move the tool back and forth over the area you want
to deep clean. Make sure to press the top (suction)
nozzle down into the surface.
9
When You Are Done Cleaning
Leave the machine on for 15 seconds
after cleaning to allow for all of the
dirty solution to be collected into the
DIRTY WATER TANK.
1 - 8 0 0 - 7 8 4 - 3 6 2 8
Upholstery
Ports
5
Turn The
Machine On
Push the POWER
SWITCH to the
UPHOLSTERY
CLEAN
position.
13
Publicité
