Publicité
Les langues disponibles
Les langues disponibles
INTENDED USE
This tool is intended to be used with the appropriate cutter to machine rivets flush with a surface.
GENERAL OPERATION
This tool is equipped with a teasing throttle. By slightly depressing the trigger, the cutter will rotate slowly. This is useful when centering the cutter over
the rivet. The tool will run at maximum speed when the trigger is fully depressed.
AIR SUPPLY
The efficiency of the tool is dependent on the proper supply of clean dry air at 90 psig (6.2 bar). The use of a line filter, pressure regulator, and lubricator
will insure maximum output and life of tools. Before connecting tool, blow out the air line to remove water and dirt which may have accumulated.
HOSE AND HOSE CONNECTIONS
Supply hose should be not less than 3/8" (10 mm) I.D. Extension hoses should be at least 1/2" (13 mm) I.D. Use couplings and fittings with at least 3/8"
(10 mm) I.D.
LUBRICATION
For maximum performance and tool life, an air line lubricator, set to deliver 2 drops per minute, is recommended. SIOUX No. 288 Air Motor Oil is recommended.
If an airline lubrication is not used, it is recommended that the tool be oiled daily before use to improve performance. Add 2-4 drops of air motor oil and
run the tool for 10-20 seconds to distribute oil through the tool.
Lubricate the gears through the grease fitting with Sioux 1232A grease after 100 hours of operation.
MAINTENANCE
Water, dust and other airline contaminants can cause rust and vane sticking. For long periods between tool use, flush the tool with a few drops of oil
and run for 10 seconds. This will help remove contaminants and reduce the formation of rust.
INSTALLING CUTTERS
•
Remove the power tool from the air hose to prevent unintended starts.
•
Remove the skirt. The skirt has a right hand thread.
•
Press the spindle lock button while slowly rotating the cutter manually. A distinct stop will be felt when the spindle lock engages the drive shaft.
NOTE: The SRS6P model requires the stabilizer accessory, if installed, to be removed to allow access to the spindle lock button. The SRS6P utilizes a
recessed spindle lock button to prevent unintended use. Use any common tool, such as a punch, or allen wrench, to press the recessed button.
•
Once the spindle is locked, replace the cutter. The cutter has a right hand thread.
•
Install the nose piece.
NOTE: Verify that the inner diameter of the skirt is sized appropriately for the outer diameter of the cutter.
•
Adjust the depth of cut.
NOTE: It is best to initially adjust the tool to cut the rivet slightly above the surface; and then, continue to adjust the tool in increments until the
desired depth is achieved.
ADJUSTING THE CUTTING DEPTH
SRS10P & SRS10S MODELS
•
Slide the adjusting ring forward, and rotate to advance, or retract the skirt to the desired cutting depth. Each graduation is .001 inches.
SRS6P MODELS
•
Unlock the lock ring (thread the lock ring towards the rear of the tool, away from the lock slide).
•
Take note of the current position of the lock slide's teeth relative to the teeth on the adjustment nut. Each advancement of position (1 tooth)
will move the cutter depth .0005 inches. Carefully pull the lock slide back and rotate the adjustment nut to the desired depth setting, and then
carefully release the lock slide to engage the desire depth setting. The lock slide is spring loaded, and will hold the lock slide in place.
•
Once the desired depth is set, return the lock ring to the "locked" position (thread the lock ring forward to assure that the depth setting is not
accidentally changed during operation).
SHAVING OR MILLING RIVETS
•
Place the nose piece over the rivet. The stabilizer will aid in maintaining proper alignment with the rivet.
•
Start the tool.
•
Press down on the tool until the cutter contacts the rivet.
•
Continue pressing until the rivet is cut flush with the surface. If the depth of cut is properly adjusted, the cutting action will stop automatically.
•
Shut off the tool and remove from the surface.
Catalog
Weight
Number
(lbs/kg)
SRS6P21-10
2.0/0.9
SRS6P21-5
2.0/0.9
SRS6P21-6
2.0/0.9
SRS6P21-7
2.0/0.9
SRS6P21-8
2.0/0.9
SRS6P21-9
2.0/0.9
SRS6P21-9W
2.0/0.9
SRS10P21-10
2.7/1.2
SRS10P21-5
2.7/1.2
SRS10P21-6
2.7/1.2
SRS10P21-7
2.7/1.2
SRS10P21-8
2.7/1.2
SRS10P21-9
2.7/1.2
SRS10S21-8
2.5/1.1
ZCE777
Form
NOISE AND VIBRATION READINGS
Sound Pressure (dBA)
Sound Power (dBA)
(per EN ISO 15744)
(per EN ISO 15744)
TBD
TBD
TBD
TBD
TBD
TBD
84
TBD
TBD
TBD
TBD
88.5
TBD
TBD
Uncertainty (dBA)
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
95.6
<3
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
100.2
<3
TBD
TBD
TBD
TBD
3
*Vibration m/s
Uncertainty m/s
2
(per EN ISO 28927-5)
(per EN 12096)
TBD
TBD
TBD
TBD
TBD
TBD
0.27
TBD
TBD
TBD
TBD
0.91
TBD
TBD
2021September8/P
Date
2
TBD
TBD
TBD
TBD
TBD
TBD
0.02
TBD
TBD
TBD
TBD
0.10
TBD
TBD
Publicité
