SIOUX SRS6P Serie Manuel D'instructions Et Pièces Détachées page 2

Tools not operated at proper air pressure can operate erratically.
Do not exceed a maximum air pressure of 90 psig/6.2 bar or as stated on the tool's nameplate or operating instructions. Use an
air regulator to maintain proper air pressure.
Erratic operation in power tools can cause injury.
Improperly repaired tools perform unpredictably.
Repair tools at an Authorized Sioux Service Center.
Tools that perform unpredictably can cause injury.
Tools left connected to the air supply can start unexpectedly.
Always remove tool from air supply and activate trigger to bleed air line before making any adjustments, changing accessories,
or doing any maintenance or service on tool. Make it a habit to check to see that all adjusting keys and wrenches have been
removed from tool before turning it on.
Tools starting unexpectedly and flying keys and wrenches can cause injury.
Working in poorly lit areas makes it hard to see hazards.
Keep work area well lit.
Poorly lit work areas can cause injury.
Children are attracted to work areas.
Keep children away. All visitors must keep a safe distance away from work area.
Children in work areas can be injured.
Unauthorized or untrained personnel can misuse unattended tools.
Store idle tools in a dry, high or locked-up place, out of the reach of children.
Misused tools can cause injury.
Tools with the actuator left in the "ON" position when an unexpected air pressure loss occurs can start unexpectedly when the air
pressure is restored.
Release the actuator if an unexpected loss of air pressure occurs.
Unexpected tool starts can cause injury.
Tools with the actuator left in the "on" position can cause unexpected starts when the tool is connected to the air supply.
Be sure actuator is off before hooking up air.
Unexpected starts can cause injury.
The use of any accessory with this tool not provided or specified by Sioux Tools can perform unpredictably.
Use only accessories provided or specified by Sioux Tools.
Tools that perform unpredictably can cause injury.
Read and understand safety instructions before installing, operating, repairing, maintaining, changing accessories on, or working
near the rivet shaver. Do not modify this rivet shaver. Do not operate this rivet shaver if it has been modified or damaged. Tools
should be inspected periodically to ensure markings are legible.
Be aware of hazards from operating the rivet shaver.
Wear gloves to protect from cuts, abrasions and heat. Operators and maintenance personnel should be physically able to
handle the bulk, weight and power of the tool. Hold the tool firmly and be ready to counteract normal or sudden movements.
Maintain a balanced body position and secure footing. High-reaction torque can develop in the case of stalling, which can
cause excessive loads being applied to the bit. Use a suspension device when possible. Keep hands away from the rotating
chuck. Release the start-and-stop device in the case of an interruption of air supply. Use only lubricants that are recommended
by Sioux Tools. Safety glasses are required.
Incorrect operation of the rivet shaver can cause injury.
Be aware of hazards from your workplace.
Be aware of slipper surfaces caused by the use of the tool and avoid trip hazards caused by the air line. Proceed with care in
unfamiliar surroundings. The rivet shaver should not be used in explosive atmospheres and is not insulated against contact
with electrical current. Ensure work area is free from electrical cables, gas pipes and other hazards.
Hazards from your workplace can cause injuries.
Operators can experience discomfort in the hands, arms, shoulders, neck or other parts of the body.
Use a comfortable, not off-posture position. Change posture during extended tasks.
If the operator experiences persistent or recurring discomfort, pain, throbbing, aching, tingling, numbness, burning sensations or
stiffness, the operator should seek medical assistance.
Accessories and bits attached to the rivet shaver can create hazards.
Disconnect the router from the air supply before changing the inserted tool. Do not touch the inserted bit during operation as
this increases the risk of cuts, burns, or vibration injuries. Do not use accessories and consumables that are not recommended
by Sioux Tools.
Improper accessories, improperly mounted accessories and tools can cause injury.
When disposing of a tool, do it in a way that does not harm personnel or the environment.
ZCE777 2021September8/P
Form 2 Date