Skil 1470 Notice Originale page 8

- mount the accessory with the depressed centre
pointing downwards
- loosen/fasten screw A with hex key B
- check the tight seating of the accessory (incorrect
or not securely fastened accessories can come loose
during operation and create a hazard)
• Mounting of sanding sheet 8
- tap the dust out of the VELCRO material on sanding
pad C 2 before mounting the sanding sheet
- mount VELCRO sanding sheet as illustrated
! the dust suction requires the use of perforated
sanding sheets
! perforation in sanding sheet should correspond
with perforation in sanding foot
! replace worn sanding sheets in time
! always use the tool with the total VeLCrO
surface covered with sanding paper
• Dust/chip extraction 9
- mount dust extraction device D as illustrated
- connect vacuum cleaner
! do not use dust extraction device/vacuum cleaner
when sanding metal
- clean dust extraction device D regularly for optimal
dust pick-up performance
• On/off
- switch on/off the tool by pushing switch E 2 in "I"/"O"
position
! before the accessory reaches the workpiece, the
tool should run at full speed
! before switching off the tool, you should lift it
from the workpiece
• Adjusting working speed 0
- with wheel F the required oscillating frequency can be
adjusted from low (1) to high (6) (also while tool is
running)
- the optimal working speed depends on the material
and can be determined with practical trials
• Holding and guiding the tool
! while working, always hold the tool at the
grey-coloured grip area(s) !
- keep ventilation slots G 2 uncovered
- do not apply too much pressure on the tool (excessive
pressure will cause excessive heat and may shorten
the service life of the accessory)
• Depth adjustment accessory (DEPTH STOP) (not
standard included) @
aPPLICaTION adVICe
• Use segment saw blade H 2 for separating and plunge
cuts in wood, plaster, gypsum and plastics (also for
sawing close to edges, in corners and other hard-to-
reach areas)
• Use plunge-cut saw blade J 2 for separating and deep
plunge-cuts in wood, plaster, gypsum and soft plastics
(also for sawing close to edges, in corners and other
hard-to-reach areas)
• For more tips see www.skil.com
MaINTeNaNCe / serVICe
• This tool is not intended for professional use
• Always keep tool and cord clean (especially ventilation
slots G 2)
! disconnect the plug before cleaning
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skil.com)
eNVIrONMeNT
• do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2012/19/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 6 will remind you of this when the need for
disposing occurs
NOIse/VIBraTION
• Measured in accordance with EN 60745 the sound
pressure level of this tool is 92 dB(A) and the sound
power level 103 dB(A) (standard deviation: 3 dB), and the
vibration ✱ (triax vector sum; uncertainty K = 1.5 m/s²)
✱ when sanding 8.8 m/s²
✱ when cutting with plunge-cut saw blade 13.9 m/s²
✱ when cutting with segment saw blade 7.2 m/s²
• The vibration emission level has been measured in
accordance with a standardised test given in EN 60745; it
may be used to compare one tool with another and as a
preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with different
or poorly maintained accessories, may significantly
increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may significantly
reduce the exposure level
! protect yourself against the effects of vibration
by maintaining the tool and its accessories,
keeping your hands warm, and organizing your
work patterns
Outil multifonctions
INTrOdUCTION
• Cet outil est conçu pour le sciage et la découpe du bois,
du plastique, des métaux et des carreaux muraux mous
ainsi que pour le polissage de petites surfaces
• En raison de la commande oscillante, l'accessoire pivote
jusqu'à 19000 fois par minute pour 3°, ce qui rend l'outil
8
1470