Publicité
Les langues disponibles
Les langues disponibles
EN
FR NL DE ES IT CS SL HR
info_out Note
When it is first used, all the LEDs will light
up to begin with. The air purifier is set at the
lowest ventilation speed.
When the "Filter Reset" light above
the
button flashes, change the
/
stop
start
combined filter.
To do this, follow the instructions in the chap-
ter on "Changing the filter".
Ventilation speed
The air purifier has four ventilation speeds:
I (low), II (average), III (high) and IV (turbo)
To move from one ventilation speed to an-
other, press the ventilation speed button
The
indicator as currently con-
ventilation speed
figured will light up on the control panel.
UV light/Night Mode
Press this button once to switch on the UV
light.
Press the button a second time to switch on
standby mode. The indicator will light up
10 times before all the indicators switch off.
Press any button to switch on the machine
and standby mode will switch off.
Press this button a third time to switch off
the UV light. The standby mode indicator
will flash 10 times and standby mode is then
switched on again.
Then press this button again to switch off
standby mode.
Timer function
The air purifier has a timer function with
which you can decide on the number of hours
after which the device must stop. The air pu-
rifier has three timer periods: 2hrs (two hours),
4hrs (four hours) and 8hrs (eight hours).
To move from one timer speed to another,
press the
button. The timer length in-
timer
dicator as currently configured will light up
on the control panel. The air purifier then
switches off automatically after the number
of hours defined.
To switch off the timer, press the
until no light is lit above the button. The air
purifier will then run with no time limit.
Changing the air filter
You must replace the three-layer filter after
4,320 hours of use. The red "Filter Reset" LED
above the
button flashes after 4,320
/
stop
start
hours of use. To replace the filter, proceed
as follows:
•
Turn the purifier upside down.
•
Unscrew the bolt under the base followed
by the base.
4
English
/ 28
E-IM-AirPurifier-001.indd 4
•
Remove the dirty filter and insert the new
filter into the device.
Put the base back in place and fix it using
the fastening nut.
Replacing the UV light
The UV light has a life of 20,000 hours.
•
Unscrew the UV light's holder:
•
Gently remove the cover and unscrew
the UV light.
•
Insert a new UV light then put the cover
back on.
•
Note: Do not look at the UV light when
it is lit.
healing TROUBLESHOOTING
sentimen Impossible to switch on
the air purifier.
help_out The casing cover has not
been installed properly.
sentimen Make sure that the casing cover
is in the right position.
help_out The three-layer filter has not
been installed properly.
sentimen Make sure that the three-layer
filter is the right position.
help_out The mains adapter is not connected.
sentimen Plug the mains adapter into
a suitable power socket.
sentimen There is insufficient throughput of air
help_out The filters are clogged.
sentimen Clean the filters (see the chapter
on "Maintenance and Storage".
help_out The air inlet/exhaust is blocked
sentimen Make sure that the air inlet/
exhaust is not blocked.
sentimen The air purifier is very noisy.
help_out There is a foreign body in
the air inlet/exhaust.
sentimen Remove the foreign body from
the air inlet/exhaust.
help_out The filters are clogged.
sentimen Clean the filters (see the chapter
on "Maintenance and Storage").
help_out The filters are not installed properly.
button
timer
sentimen Reposition the filters correctly.
help_out The air purifier is standing on
a very uneven surface.
sentimen Put the air purifier on a flat surface.
MAINTENANCE
report_p Install the air purifier
Before cleaning the device, check that the air
purifier's power supply is fully disconnected.
Clean the air purifier's casing with a slightly
damp cloth (with water or a gentle cleaning
solution). Do not use thinner or other corro-
sive or abrasive cleaning products because
the surface might get damaged.
report_p Clean the filter
Only the pre-filter is washable. Check that
it is dry before fixing to the HEPA filter and
activated carbon filter.
The filter needs to be cleaned regularly (once
a month) for efficient and hygienic use. Clean
the three-layer filter with the nozzle of a
vacuum brush. For a full clean, remove the
pre-filter, then clean the carbon filter and the
HEPA filter with the nozzle of a vacuum brush.
Then replace the pre-filter on the HEPA filter.
The three-layer filter must be replaced after
4,320 hours of use (see chapter on "Changing
the air filter").
STORAGE
If you do not use the device for a prolonged
period, we recommend that you store it once
cleaned in its original packaging and do not
put anything on top of it.
TECHNICAL DATA
Model
LA120209
Voltage
220-240V
Power
45W
Dimensions
200 × 200 × 328 mm
Weight
2.9kg
Covered surface ±15m²
Conditions
+5°C a +40°C, ≤90% relative air
of use
humidity (non-condensing)
Safety category Safety category II /
CADR
100m³/hr
UV light
Wave length: 254 nanometres
Light lifespan: Approx. 20,000 hours
HEPA filter
E11 HEPA filter
+ Activated
HEPA filter + Activated carbon
carbon filter
Filter lifespan: 4320h
Sound level
Level 1 <32dB; Level 2 <37dB;
Level 3 <47dB; Turbo <60dB
ADVICE ON WASTE
DISPOSAL
The packaging consists entirely of environ-
mentally-friendly materials that can be taken
to your local waste sorting centre to be used
as secondary materials. Cardboard can be
placed in a paper collection container. Pack-
ing film must be taken to your local sorting
and recycling centre.
When you are no longer using the device, dis-
pose of it in an environmentally responsible
manner and in compliance with the statutory
requirements.
LIMITED WARRANTY
LANAFORM guarantees that this product will
be free from any material and workmanship
defects for a period of two years from the
date it was purchased, other than as spec-
ified below.
The LANAFORM warranty does not cover
damage caused by normal wear and tear on
this product. In addition, the warranty on this
15/06/2018 11:57:17
Publicité
