Publicité
Les langues disponibles
Les langues disponibles
For a good washing quality, soaking the dishes
before putting them inside the machine is advised.
Otherwise the food residue, lemon peels, toothpick
etc. materials can block the materials drain pump
and alter the washing quality.
An integrated dish washing system can be formed
in the device by installing units such as; scraping
unit, dust cart, bench with sink support and output
bench.
For the washing process in the device, use liquid
and foam free detergent. Amount to be used must
be determined by the detergent manufacturer. Also,
the amount of polisher to be used must be
determined by the manufacturer firm. Detergent
and polisher placement units are also made by the
manufacturer firms.
Select the most suitable program according to the
type and/or dirtiness of the dishes to be washed.
As standard accessory; there is 1 plate, 1 cutlery, 1
glass tray in 500x500 mm size in the machine.
Select the relevant tray according to the dishes to
be washed and load them according to the
capacities stated on the chart. Do not start the
device without entirely filling the tray in order to
save detergent and power.
Never change the location of the device while it is
operating.
Be sure that the water input valve is open before
operating the device.
WARNING!!!
NEVER PUT YOUR BARE HANDS IN THE
WASH
WATER.
PROTECTIVE
GLOVES.
DETERGENT WATER ON YOUR EYES.
9. TURNING OFF
The device is turned off by holding down the
ON/OFF button for 2 seconds.
Bring the switch that supplies the device to "0"
position.
Take the washed product out by lifting the upper
cover and close the cover.
Close the water inlet valve.
10.SECURITY MEASURES
If the cover is opened while the device is operating
or if the cover is not completely closed after it is
started, the device will stop operating. Device will
start operating once the cover is shut.
WARNING: If there are any damages on the
energy input cable or any water leakage on the
release pump, the device needs to be shut down and
an authorized service must be notified.
10.DAILY MAINTENANCE
The wash water must be renewed at least two times
a day or when the water loses its ability to clean
due to dirty particles. Washing performed with
IF
NECESSARY,
DO
NOT
dirty wash water causes bad washing results, along
with detergent, polisher and power wastage.
Before starting maintenance activities, turn off the
power switch that the device is connected to.
Be careful so that the dirty water outlet is not
blocked.
Check whether the washing and rinsing arms can
turn easily. Check the water sprays and if they are
blocked, clean the holes with a thin stick.
Leave the cover open after cleaning the device.
WARNING; In order not to damage the
electrical equipment, clean the device with a
direct or high pressured water.
11.PERIODIC MAINTENANCE( once every
2-3 days)
Never do maintenance while the device is powered.
As shown in Figure 1, materials that can cause
blocking must be cleaned by taking out the nozzles
of the water sprays.
Clean the outer surfaces of the device with a wet
and soapy cloth. While cleaning the surface of the
device, do not use materials that can leave marks
on the surface such as detergents, wire brushes etc.
which have abrasive content.
Clean the device warmers with an anti-lime once a
week.
Take out and clean the pump front filter in certain
periods.
If the device will not be used for a long time, the
USE
RUB
surfaces need to be covered with Vaseline in thin
layers.
Contact the authorized service in case a dangerous
situation is noticed in the device. Do not let
unqualified people to interfere the device.
After a certain operating duration, depending on
the hardness of water, the calcium and magnesium
in the water can cause the forming of boiler scale
on the interior surfaces of the wash tank, boilers
and interior sections of the water pumps which can
affect the devices performance. For this reason, a
boiler scale cleaning process must be performed by
a qualified technician over time.
Maintenance of the boilers, emptying the water
inside the boiler and pump and cleaning them must
be performed by qualified people periodically.
If there is a danger of freezing during the times
when the machine hasn't worked for a long time,
the wash pump and boiler must be emptied.
Contact the authorized service in case a dangerous
situation is noticed in the machine. Do not permit
unqualified people to interfere the device.
12
Publicité
