Elettro CF INVERTER PRO MIG 466 PULSED Manuel D'instructions page 18

Parameters being the same, it determines the mesh diameter
and therefore the penetration.
3.3.1.13.4 "Arc Length Cor".
Sets arc length of the higher speed/current.
Warning: make sure that the arc length is the same for both
currents.
3.3.1.14. "Preflow".
(In all processes except MMA).
Pre Gas
3.3.1.15. "Postflow".
(In all processes except MMA).
Post flow
3.3.1.16. "Speed Corr". (only in MIG HD processes).
Allows the percentage correction of the wire speed as compared
to the preset speed.
Speed Correction
3.4. "JOB" MENU.
In this section you can save, modify, restore, copy or can- cel
the working programs.
From the " Main Menu ", with key T7, highlight the "Jobs" item
and enter the submenu by means of key T6.
3.4.1. Saving of a "JOB" program.
Once the adjustments and the settings described above have
been made, with keys T5 and T7 select a position in the memory
and press key U8 (SAVE) to save.
keys U8, U7, U6 and U5:
- DEL: cancels the selected "Job".
- RCL: restores the selected "Job" to modify it.
- COPY: copies the selected "Job" and saves it in a different
position.
3.5. MENU "Settings".
In this section you can set or modify the welding machine main
settings.
Via key T6 enter the submenu related to the selected parameter.
MIN MAX DEF.
0 s 10 s 0.1 s
MIN MAX DEF.
0 s 10 s 3 s
MIN MAX DEF.
-99% +99% 0.0%
The "Job" program number, the
welding process and the wire
diameter are shown on
display.
When a "Job" has been saved,
the lower display shows the
abbreviations corresponding to
From the "Main Menu" (see par.
3.3), select menu "Settings" via
key T7 and display it with key T6.
All the parameters that the
operator may modify are listed
here:
- Welding
- Machine
- Factory Setup
- Languages
3.5.1. Menu "Welding".
This submenu includes a list of welding parameters that can be
modified:
- H2O MIG/TIG This function allows the setting of the cooling
unit start-up.
Range: ON-OFF-Auto (DEF ON).
If "Auto" is selected, when the machine starts, the unit is
running. If the torch trigger is not pressed after 30 seconds, it
shuts off. When the torch trigger is pressed, the unit starts
operating and shuts off 3 minutes after the torch trigger is
released.
- "Quality Control"
ON - OFF Setting (DEF OFF) (Available on demand).
- "Max inching"
The purpose is to stop the welding machine if the wire lows
for the preset length in cm after starting with no passage of
current. OFF Setting - 50 cm (DEF OFF).
- "Push-Pull Force"
This function adjusts the drive torque of the push-pull motor
in order to make the wire feed linear.
3.5.2. "Machine" Menu - " Machine Settings".
Here is available the following submenu:
- "Clock Setup".
3.5.3. "Factory Setup" Menu - "Resetting of preset values".
This item allows return to the factory preset values. Three
resetting modes are possible:
- All
- Jobs only
- Exclude jobs Resets all but saves "Job" working programs.
3.5.4. "Languages" Menu - "Language setup".
In this section you can select the language of the messages
displayed.
3.6. INFORMATION MENU.
Data concerning the power source software are displayed in this
section.
the
3.7. QUICK START-UP.
In the V1 display lower side, a few controls appear for the quick
access to the most common functions, related to the various
pages.
3.7.1. "MEM" - "SAVING" (see par. 3.4.1).
If you wish to save a welding program, press key U8, select keys
T5 and T7, the "Job" number and then press key U8 again to
save the welding condition.
3.7.2. "PAR" - "PROCESS PARAMETERS" (see par. 3.3.1.)
3.7.3. "2T/4T" - "TWO STAGES/ FOUR STAGES" (see par.
3.3.1.7).
3.7.4. "JOB" - "WORKING JOBS".
If you wish to use a previously saved working program, press
key U5 (JOB).
In order to see all the program settings, save the selection with
key U5 (OK), then press key U7 (PAR).
3.7.5. "H2O". (see par. 3.5.1.).
18
Complete resetting.
Resets only "Job" working programs