Calpeda GX 40 Mode D'emploi page 9

thermic dilation of the oil.
The quantity of oil to be inserted in the chamber is:
0.2 litres for GX 40;
0.5 litres for GM 50.
Use white oil suitable for food machinery and
pharmaceutic use.
For the GM 50 pumps a normal engine oil of the
SAE 10W-30 type can also be used.
Cross section drawings
96 .0 8
96 .1 0
96 .0 9
96 .0 7
7 6 .6 3
8 2 .0 3
8 2 .0 2
8 2 .0 4
8 1 .0 0
7 8 .0 0
7 3 .0 0
(3 )
1 4 .4 6
1 4 .4 7
7 6 .6 0
1 4 .2 2
1 4 .2 4
1 4 .2 0
2 8 .0 0
G X VG X C
1 2 .0 0
3 .94 .0 3 5
1 2 .2 1
96 .0 9
96 .0 8
7 6 .0 4
96 .0 0
7 3 .0 0
3 6 .0 0
(2 )
7 0 .0 0
1 4 .2 0
1 4 .4 6
2 8 .0 0
(1 )
2 8 .2 0
7 6 .6 0
G M V
1 2 .2 0
7 0 .1 3
7 0 .1 1
7 0 .1 2
96 .0 0
7 8 .1 2
8 2 .0 5
(1 )
8 2 .0 1
(1 )
7 6 .0 1
(1 )
G M C
3 .94 .0 2 4 .1
8. Queries and spare parts
In your queries and orders please mention the
pump name-plate data. Alternatively, if the bar-code
label has been saved, mention the numbers on the
label or enclose a photocopy of it.
When ordering
designations and drawing position numbers.
Changes reserved.
7 6 .0 4
7 6 .6 2
7 0 .0 5
7 6 .6 3
7 6 .6 6
7 6 .6 4
7 6 .6 5
7 6 .0 2
6 4 .1 2
6 4 .0 8
4 0 .0 0
(2 )
7 0 .0 0
3 6 .0 0
1 4 .0 0
2 8 .0 0
7 3 .0 8
2 8 .2 0
2 8 .0 8
2 8 .0 4
7 6 .6 4
8 2 .0 4
8 1 .0 0
7 8 .0 0
7 6 .0 0
94 .1 2
G M C 5 0 -6 5
94 .0 4
G M V 5 0 -6 5
94 .0 0
1 4 .2 4
1 4 .0 0
2 8 .0 0
2 8 .0 4
1 2 .0 0
4 .94 .0 6 1
spare parts quote
Nr. Designation
12.00 Casing cover
12.20 Screw
12.21 Nut
14.00 Pump casing
14.20 Casing gasket
14.22 Fastening ring
14.24 Screw
14.46 Plug
14.47 Gasket
28.00 Impeller
28.04 Impeller nut
28.08 Washer
28.20 Key
36.00 Mechanical seal
40.00 Radial shaft seal
64.08 Shaft sleeve
64.12 O-ring
70.00 Motor cover, pump side
70.05 O-ring
70.11 Cable gland ring (float switch)
70.12 Cable gland ring
70.13 Washer
73.00 Pump side bearing
73.08 V-Ring
76.00 Motor casing with winding
76.01 Motor jacket with winding (1)
76.02 Kit, motor jacket
76.04 Cable gland
76.60 Float switch
76.62 Jacket cover
76.63 Screw
76.64 Handle
76.65 Handle clamp
76.66 Washer
78.00 Shaft with rotor packet
78.12 O-ring
81.00 Bearing
82.01 Motor end-shield, non-drive end (1)
82.02 Screw
82.03 O-ring
82.04 Compensating spring
82.05 Screw (1)
94.00 Capacitor
94.04 Capacitor collar
96.00 Cable
96.07 Cable fastener
96.08 Clamp
96.09 Screw
96.10 Nut
(1) Cannot be supplied separately
(2) Oil
(3) Grease
part
9