ETI 64222401 Guide D'utilisation Et D'entretien page 2

SUSPENSION MOUNTING
Bend each of the mounting clips on the back of the fixture upward.
11b
Connect the mounting clips to the aircraft cables by using S hooks.
Adjust the aircraft cables to level the fixture.
NOTICE: The LED flat panel must hang a minimum of 3 in. from the ceiling.
12b
Make the electrical connections. See Making Electrical Connections.
13b
Restore power at the electrical panel.
Turn on the light switch to activate the fixture.
SURFACE MOUNTING
× 2
×2
Use screws to assemble 3 sides of the
9c
surface mounting kit.
Ceiling
Slide the fixture into the surface mounting
12c
kit and use screws to secure the remaining
piece of the surface mounting kit.
AC-N AC-L GND
L
N
N
L-OUT
L
N
PG
PG
L
N
WITH SENSOR WIRING DIAGRAM
WARNING: Carefully read and understand the information given in this manual before beginning the assembly and installation. Failure to do so could lead to electric shock, fire, or
other injuries which could be hazardous or even fatal. • Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker. • Risk
of Electric Shock • Suitable for indoor and damp locations. • Do not mount near flammable materials or electric heaters. • Do not let power supply cords touch a hot surface. • The
product should be installed and operated by a qualified electrician or technician in accordance with relevant local codes. • The final installation must be approved by the appropriate
qualified electrical/building inspector(s).
NOTICE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna, increase the separation between the equipment and the receiver, connect the equipment into an outlet on a circuit different from that to which
the receiver is connected, and consult the dealer or an experienced radio/TV.
• Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
See website for Warranty, Troubleshooting or Care and Cleaning details at www.ETiSSL.com.
If installing into drywall, drill four 1/4 in. diameter
10c
holes into the ceiling, insert drywall anchors into
the holes, and use screws to secure the surface
mounting kit to the ceiling.
NOTICE: ETI surface mount kits can be applied
to many installation applications. Installer is
responsible to ensure kit compatibility with
attachment method to surface or structure in
accordance with any local code requirements for
installation and inspection.
Make the electrical connections. See Making
11c
Electrical Connections.
LED panel light
DIM-
SENSOR
DIM+
DRIVER-
DRIVER+
LED DRIVER
DRIVER-
DRIVER+
DRIVER+
DRIVER-
EMERGENCY
LED+
LED
LED-
LAMP
DRIVER
INDICATOR LIGHT
TEST SWITCH
Questions, problems, missing parts? Call ETiSSL Customer Service 8 a.m. - 5 p.m., CST, Monday - Friday
1-855-ETI-SSLI (1-855-384-7754) www.ETiSSL.com
Rotary fixing
Adjust the length of
suspension wire
Suspension wire
Restore power at the electrical panel.
13c
Turn on the light switch to activate the fixture.
AC-N AC-L GND
Ceiling
Ceiling
WALL SWITCH
DIM-
L
DIM+
N
LED DRIVER
DRIVER-
PG
DRIVER+
DRIVER+
PG
DRIVER-
EMERGENCY
LED+
N
LED-
DRIVER
L
NO SENSOR WIRING DIAGRAM
LED panel light
LED driver box
LED
LAMP
INDICATOR LIGHT
TEST SWITCH