Teletext Services; Software Upgrade; Troubleshooting & Tips; Av And Hdmi Signal Compatibility - AYA A32HD0122B Mode D'emploi

Select Channel: Using this option, you can switch to the
selected channel.
Set Timer on Event / Delete Timer on Event: After you
have selected an event in the EPG menu, press the OK
button. Select Set Timer on Event option and press the
OK button. You can set a timer for future events. To cancel
an already set timer, highlight that event and press the
OK button. Then select Delete Timer on Event option.
The timer will be cancelled.
Notes: You cannot switch to any other channel or source
while there is an active timer on the current channel.
It is not possible to set timer for two or more individual events at
the same time interval.

Teletext Services

Press the Text button to enter. Press again to activate
mix mode, which allows you to see the teletext page and
the TV broadcast at the same time. Press once more to
exit. If available, sections in the teletext pages will become
colour-coded and can be selected by pressing the coloured
buttons. Follow the instructions displayed on the screen.
Digital Teletext
Press the Text button to view digital teletext information.
Operate it with the coloured buttons, cursor buttons
and the OK button. The operation method may differ
depending on the contents of the digital teletext. Follow
the instructions displayed on the digital teletext screen.
When the Text button is pressed again, the TV returns
to television broadcast.

Software Upgrade

Your TV is capable of finding and updating the firmware
automatically via the broadcast signal.
Software upgrade search via user interface
On the main menu select System>Settings and then More.
Navigate to Software upgrade and press the OK button.
In Upgrade options menu select Scan for upgrade and
press OK button to check for a new software upgrade.
If a new upgrade is found, it starts to download the
upgrade. After the download is completed confirm the
question asking about rebooting the TV by pressing the
OK to continue with the reboot operation.
3 AM search and upgrade mode
Your TV will search for new upgrades at 3:00 o'clock if
Automatic scanning option in the Upgrade options
menu is set to Enabled and if the TV is connected to an
aerial signal. If a new software is found and downloaded
successfully, it will be installed at the next power on.
Note: Do not unplug the power cord while led is blinking during
the reboot process. If the TV fails to come on after the upgrade,
unplug, wait for two minutes then plug it back in.
Troubleshooting & Tips
Tv will not turn on
Make sure the power cord is plugged in securely to wall
outlet. Check if batteries are exhausted. Press the Power
button on the TV.
Poor picture
• Check if you have selected the correct TV system.
• Low signal level can cause picture distortion. Please
check antenna access.
• Check if you have entered the correct channel frequency
if you have done manual tuning.
• The picture quality may degrade when two devices are
connected to the TV at the same time. In such a case,
disconnect one of the devices.
No picture
• This means your TV is not receiving any transmission.
Make sure the correct source has been selected.
• Is the antenna connected properly?
• Is the antenna cable damaged?
• Are suitable plugs used to connect the antenna?
• If you are in doubt, consult your dealer.
No sound
• Check if the TV is muted. Press the Mute button or
increase the volume to check.
• Sound may be coming from only one speaker. Check the
balance settings from Sound menu.
Remote control - no operation
• The batteries may be exhausted. Replace the batteries.
Input sources - can not be selected
• If you cannot select an input source, it is possible that no
device is connected. If not;
• Check the AV cables and connections if you are trying to
switch to the input source dedicated to the connected device.

AV and HDMI Signal Compatibility

Source
Side AV
HDMI
(X: Not Available, O: Available)
In some cases a signal on the TV may not be displayed
properly. The problem may be an inconsistency with
standards from the source equipment (DVD, Set-top
box, etc. ). If you do experience such a problem please
contact your dealer and also the manufacturer of the
source equipment.
English - 14 -
Supported Signals
PAL 50/60
NTSC 60
480I 60Hz
480P 60Hz
576I, 576P 50Hz
720P 50Hz,60Hz
1080I 50Hz,60Hz
24Hz, 25Hz
1080P
30Hz, 50Hz,
60Hz
Available
O
O
O
O
O
O
O
O