SERVODAN 77-050 Notice D'utilisation page 6

Without remote control
Function
2 zone daylight control 1-10 V, plus on/off control of blackboard light.
App. Class
Classroom with blackboard light, factory settings
Function description:
Ceiling light
Two zones are switched on and off via a low-voltage pushbutton
switch, 1-10 V daylight control (zone 1 and zone 2).
The light can be switched on when light is needed according to the
preset parameter.
As long as the movement sensor registers activity the lighting will
remain independently daylight-controlled in two zones according
to the preset parameters. As daylight increases, lighting in the
room starts to dim until the set minimum light level is obtained. If
there is suffi cient daylight in the two zones the lighting turns off
independently in each zone. One light sensor controls both zones.
The light switches off automatically after a preset period, when the
movement sensor does not register activity within the detection range.
Dimming of lighting
By means of a long press on the low-voltage switch (Pushbutton 1),
the lighting in zones 1 and 2 can be dimmed down/up.
Blackboard light
Via a low-voltage switch (Pushbutton 2), the blackboard light is
switched on and off, on/off relay.
The light can be switched on regardless of daylight.
The light switches off automatically after a preset period, when the
movement sensor does not register activity within the detection range.
Facility for manual override via remote control (Accessories).
Settings
Factory settings:
Application: ...............................................App. Class
Lux 1 indoors (Lx 1): ..................................200 lx.
Setpoint 1 (Set 1): ......................................300 lx.
Lux 2 indoors (Lx 2): ..................................150 lx.
Setpoint 2 (Set 2): ......................................300 lx.
Off delay (Time): ........................................10 mins
Vout min 1-10 V (Dim down): .....................0 V
Vout max 1-10 V (Dim up): ........................10 V
Relay On/Off (Off delay + 10 mins.): ...........20 mins.
Operation ....................................................Pushbutton 1 for on/
When using factory settings, light sensor value of 450 lx is used
for calculating the daylight factor.
Servodan A/S | Tel +45 7442 4726 | Fax + 45 7442 4035 | info@servodan.dk | www.servodan.com
off and dimming ceiling
light
Pushbutton 2 for on/
off of blackboard light
Movement sensor off delay:
Fade to minimum after 10 min.
Switch off after 15 mins, 10 mins (off delay) + 5 mins. (cut-off delay)
LED indicator:
The LED fl ashes when the low-voltage pushbutton switch or the IR
remote control is activated.
The LED does not fl ash when activity is detected by the movement
sensor.
Manual dimming via low-voltage switch:
When the dim function has been activated, the lighting must
be switched off before being switched on, so that it can then
function with daylight control (according to light sensor).
With remote control
Function
2 zone daylight control 1-10 V, plus on/off control of relay.
App. Man
Manual, selected via IR remote (App. Man).
Function description:
Ceiling light
Two zones are switched on and off via a low-voltage pushbutton
switch, 1-10 V daylight control (zone 1 and zone 2).
The light can be switched on when light is needed according to the
preset parameter.
As long as the movement sensor registers activity the lighting will
remain independently daylight-controlled in two zones according
to the preset parameters. As daylight increases, lighting in the
room starts to dim until the set minimum light level is obtained. If
there is suffi cient daylight in the two zones the lighting turns off
independently in each zone. A light sensor controls both zones.
The light switches off automatically after a preset period, when
the movement sensor does not register activity within the
detection range.
Manual on/off of lighting
If two low-voltage pushbutton switches are used, the lighting in
zone 1 and zone 2 can be switched on and off individually.
Dimming of lighting
A long press on the low-voltage pushbutton switch enables the
lighting in zones 1 and 2 to be dimmed down/up.
If two low-voltage pushbutton switches are used, the lighting in
zone 1 and zone 2 can be dimmed individually.
Relay On/Off
When the movement sensor registers activity, the relay closes (On).
The relay switches off automatically after a preset period, when
the movement sensor does not register activity within the
detection range.
Preset off delay + 10 mins.
Manual override via remote control.
GB
6(21)