Sharp XL-B512 Mode D'emploi page 6

6
30. NUMBER (0-9): Use to select tracks or enter frequency.
31. SAVE: Press to save your favourite stations.
Fitting or replacing the remote control batteries
1.
To open the battery compartment, push your thumb down on to
the circle on the battery compartment cover and slide it down.
2.
Fit two batteries observing polarity +/- as shown. When replacing
the batteries, use only the same type of battery supplied.
3.
Re- t the battery cover and clip it in place.
Preparation for use
3
4
7
5
AUX IN
1. Place a speaker on either side of the main unit, preferably at the same
height and with at least 150mm space between each speaker to the
main unit.
Connect the speaker plugs to the rear of the unit. Take care to match
the speaker placed to the LEFT to the LEFT output on the rear of the
unit. Repeat for the RIGHT speaker.
2. Please ensure that the voltage marked on the rating label, located
on the rear panel, is the same as the voltage in your area. Insert the
gure 8 end of the power lead in to the AC IN socket on the back
of the unit. Plug the other end of the cable in to the wall socket.
3.
Press the STANDBY button on the main unit to turn it ON.
Extend the ANTENNA to get the best reception. Press the source
button on the unit, or FM button on the remote control to enter
the FM mode. To use the radio in FM mode, follow the instructions
in the FM RADIO OPERATION chapter of the User manual.
4.
Press the source button
remote control button to enter the CD mode. Press the
to open the disc drawer and insert a disc. Press the
again to close. The CD will begin playing from the rst track.
5. Press the source button
the remote control button to enter the Aux In (Audio) mode.
Connect your audio device to the AUX IN socket via a 3.5mm aux
in cable. Control playback via your connected audio device.
1
6
AUDIO IN
on the unit, or CD button on the
button
button
on the unit, or AUX button on
6. Press the source button
remote control button to enter the Bluetooth mode. Activate
the Bluetooth enabled device and select the "SHARP XL-
B512". Select the song you want and press to play.
7.
Press the source button
control to enter the USB mode. Plug the USB device to USB port on the
front panel of the unit, and it will read the USB and play automatically.
BASIC FUNCTIONS
Switching modes
To switch between the modes: CD, FM, Bluetooth, USB and AUX IN, press
SOURCE button on the unit or the corresponding button (FM, CD, , AUX,
USB) on the remote control.
Volume control
1.
Increase: Rotate the VOLUME control on the main unit
clockwise or press the VOL+ button on the remote.
2.
Decrease: Rotate the VOLUME control on the main unit anti-
2
clockwise or press the VOL- button on the remote.
EQ eff ects
Press the EQ button on the remote repeatedly to cycle through a set of
equaliser presets to adjust the sound. Choose from CLASSIC, ROCK, POP,
JAZZ, DANCE, LIVE and O .
Loudness function
This function will increase the level of bass at low volume levels. Press the
LOUD button on remote to enable the e ect. Press again to disable the
e ect.
Mute function
Press the button at any time to mute the sound output. Press again to
unmute.
Tone controls
To adjust the bass, use the BAS+ or BAS- buttons on the remote control.
To adjust the treble, use the TRE+ or TRE- buttons on the remote control.
Standby mode
Press the STANDBY button on the unit or the remote to put the system
into standby mode. To resume normal operation, press this button again.
NOTE: This unit is designed to enter STANDBY mode automatically, after about
15 minutes (approximately) of inactivity. Press STANDBY button to wake the
unit.
NOTE: When you power on the unit from standby, it will resume in the mode
that was last used.
FM radio operation
1.
Press the source button
control to enter the FM mode. (FM frequency: 87.50-108.00MHz)
2. /
Press the buttons on remote control to decrease
or increase the frequency in 0.05MHz increments.
3.
Press and hold the
to scan through the frequency range quickly. The
scan will stop once it has found a station.
4. Press and hold the
range quickly; it will store any stations found automatically.
5. SAVE a station:
You can store up to 40 FM stations in memory.
Press the FREQ button and then, using the number
buttons enter the frequency that you want to store.
Press the SAVE button, it will show " P01" on the display.
on the unit, or button on the
on the unit, or USB button on the remote
on the unit, or FM button on the remote
/
buttons on remote control
button to scan through the frequency