Gemini PS-626USB Manuel D'instructions page 5

CONTROLS:
(CONTINUED)
CHANNEL ROTARY GAIN
13
The CHANNEL ROTARY GAIN allows you to boost the signal of each
individual channel depending on how low or high its input level is
14
3 BAND EQUALIZER
The 3 BAND EQUALIZER adjust the tone of each CHANNEL by giv-
ing you a choice 3 frequencies (BANDS) to adjust , from LOW,
MIDRANGE (MID) and HIGH's ,you can use the adjustment knobs to
higher or lower the 3 separate frequencies till the sound of the music
program is appropriate for your listening environment.
15
CHANNEL VOLUME FADER
After you have chosen which input you will use with the INPUT SE-
LECTOR the corresponding CHANNEL FADER will allow you to ad-
just the volume for that particular CHANNEL.
16
FADER ADJUSTMENT SWITCHES
The fader adjustment switches allow you to change the functionality
of the fader. The REVERSE switch when in the ON position will flip
the fader so it works in REVERSE ie. channel (1) on the left and chan-
nel (2) on the right. The CURVE selector lets you choose between two
fader CURVE settings, positioning the switch to the left will give you a
gradual CROSSFADE and positioning the switch to the right will give
you a quick CROSSFADE.
17 CROSS FADER
The CROSS FADER allows you to mix evenly from one source to an-
other. On the PS-626USB The CROSS FADER is assignable between
all (5) channels. The CROSS FADER on the PS-626USB is also re-
movable and if the need arises can be replaced.The RG-45 (RAIL-
™
GLIDE ) DUAL-RAIL CROSS FADER, which has internal dual
stainless steel rails that allow the slider to ride smoothly and accu-
rately from end to end can be purchased from your local GEMINI
dealer.
NOTE: WHEN USING THE CROSS FADER LIGHTLY GLIDE THE
FADER BACK AND FORTH. PRESSING DOWN ON THE CON-
TROLS CAN BEND CONTACTS AND CAUSE A LOSS OF SOUND.
VU METER
18
The PS-626USB has a VU METER that allows you to monitor the
decibel levels of the LEFT and RIGHT MASTER output.
19 CUE MASTER SWITCH
The VU METER has two display modes, in CUE mode it will display
the level of the channel you are cueing, in MASTER mode it displays
the main MASTER output.
20
MASTER VOLUME ROTARY
The MASTER VOLUME ROTARY knob adjust the volume of the
MAIN output
21 CUE/PGM ROTARY
The CUE/PGM ROTARY determines the mix between the chosen
CHANNEL CUE SELECTOR and the MAIN OUTPUT mix.
22
CUE VOLUME ROTARY KNOB
The CUE VOLUME ROTARY KNOB adjusts your HEADPHONE
MONITOR OUTPUT'S volume.
19 23 CHANNEL CUE SELECTOR
The CHANNEL CUE SELECTOR allows you to choose which chan-
nel you wish to monitor in your headphones.
PS-626USB
USB SETUP:
ON A PC
Open the START menu and go to CONTROL PANEL, once in the
control panel folder click on the SOUND AND AUDIO DEVICES
ICON, when the SOUND AND AUDIO DEVICES window opens
click on the AUDIO pane, then under SOUND PLAYBACK choose
the USB AUDIO CODEC as a DEFAULT DEVICE,then you just click
on APPLY and you are ready to use the PS-626USB with your PC.
ON A MAC
Under the APPLE menu open SYSTEM PREFERENCES, and in
SYSTEM PREFERENCES choose the SOUND icon, once in the
SOUND window choose the OUTPUT pane and under CHOOSE A
DEVICE FOR SOUND OUTPUT select USB AUDIO CODEC.
Repeat the procedure for the INPUT pane, now your MAC is ready to
work with the PS-626USB.
FADER REPLACEMENT:
1. UNSCREW THE FADER (B)
SCREWS. DO NOT TOUCH INSIDE
SCREWS (C) CAREFULLY RE-
MOVE OLD CROSS FADER AND
UNPLUG CABLE (D)
2. PLUG IN THE NEW CROSS
FADER INTO CABLE (D) AND
PLACE BACK INTO MIXER.
3. SCREW THE CROSS FADER TO
MIXER WITH THE FADER PLATE
SCREWS (B)
4. REPLACE THE FACE OF THE MIXER AND SCREW THE FOUR SCREWS
BACK IN AND REPLACE THE FADER KNOBS.
SPECIFICATIONS:
INPUTS:
Phono............................................................................3mV,47 K Ohm
Line.........................................................................150 mV, 27 K Ohm
MIC.............................................................1.5 mV, 1 KOhm Balanced
OUTPUTS:
Max..........................................................................20V Peak-to Peak
Rec............................................................................225 mV, 5 K Ohm
GENERAL:
Frequency Response.........................................20Hz - 20KHz +/- 2dB
Distortion..................................................................................< 0.02%
S/N Ratio...................................................................Better than 85 dB
Headphone impedance..............................................................8 Ohm
Power Source ..............................................................AC 15v 500mA
Unit dimensions............................................................10" x 3.3" x 12"
.............................................................................(254 x 84 x 304 mm)
Weight.........................................................................6.5 lbs (2.94 kg)
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTIFICATION FOR IMPROVE-
MENT
5