EINHELL GE-WS 18/35 Li Instructions D'origine page 22

indicator on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
•
the charger
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
5.5 Battery charge level indicator (Fig. 7)
Press the button for the battery charge level indi-
cator (Item A). The battery charge level indicator
(Item B) shows the charge status of the battery
using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
Anl_GE_WS_18-35_Li_SPK13.indb 22 Anl_GE_WS_18-35_Li_SPK13.indb 22
GB
5.6 Preparing spray solution and fi lling the
container
Switch off the equipment and remove the battery.
Note:
•
Always follow the manufacturer's instructions
when mixing spray solutions. Fill the tank only
with the amount of solution you intend to use.
•
Spray solution must have a water-like consis-
tency.
•
GE-WS 18/35 Li: The spray container can be
filled with a maximum 3.5 liters of liquid.
•
GE-WS 18/75 Li: The spray container can be
filled with a maximum 7.5 liters of liquid.
•
Pesticides must only be prepared outdoors
and never in living quarters, stables, or sto-
rage rooms for food and animal feed.
•
Spray solutions can be prepared in a sepa-
rate container and mixed thoroughly before
being filled into the container of the pressure
sprayer.
•
If you intend to use organic spray solutions,
they must be filtered prior to filling the sprayer.
•
Clean the equipment immediately after each
use. This is the only way to keep the liquid-
carrying parts clean and prevent clogging.
Clogged components can lead to defects.
1. Place the pressure sprayer on a level surface.
Remove the tank cap (Fig. 8/Item 10). This
also serves as a measuring jug.
2. Pour the amount of liquid (e.g. water) spe-
cifi ed by the solution manufacturer into the
spray container (Fig. 9). If the spray solution
has not been prepared ready for spraying,
add the measured quantity of concentrated
additive and close the container carefully.
3. If you have not already done so, mix the con-
centrated additive with the water (or other
liquid) by shaking the pressure sprayer.
4. Apply the label for the spray solution used to
the spray container (Fig. 10).
6. Operation
6.1 Switching on
After inserting the battery, switch the equipment
on by turning the On/Off switch to the "I" position
(Fig. 11).
6.2 Switching off
Switch the equipment off by turning the On/Off
switch to the "0" position (Fig. 11).
- 22 -
14.06.2022 14:17:41 14.06.2022 14:17:41