Oil & Fuel Recommendations; Fueling - Jiffy 3500 Serie Manuel D'utilisation

•
DO NOT RETURN your Jiffy Power Ice Drill TO THE
RETAILER THAT SOLD IT TO YOU. THEY MAY NOT BE
AUTHORIZED TO PROVIDE REPAIRS OR WARRANTY
REPLACEMENT. If you have any questions concerning
service, contact Feldmann Engineering as indicated in the
Service & Repair Information section of this manual.
ASSEMBLY AND DISASSEMBLY OF DRILL AND POWERHEAD
Jiffy E-Z Connect™ Collar
Connect drill assembly to powerhead by sliding E-Z Connect™
Collar down and pulling clevis pin out. Then slide drill assembly onto
output shaft. Reinsert clevis pin through drill assembly and output
shaft, then slide E-Z Connect™ Collar up and twist collar slightly to
lock pin in place.
Note: Do not remove clevis pin from collar tether.
OIL & FUEL RECOMMENDATIONS
IMPORTANT NOTE: A 40-1 MIXTURE OF FRESH WINTER BLEND
GAS AND HIGH QUALITY 2-CYCLE OIL IS NEEDED TO RUN THIS
ENGINE. NEVER RUN ON STRAIGHT GAS, OR ANY MIXTURE
OTHER THAT 40-1 AS SERIOUS ENGINE DAMAGE WILL
RESULT AND VOID ALL WARRANTY OF YOUR ENGINE.
TO OPERATE YOUR DRILL, YOU WILL NEED THE FOLLOWING:
CLEAN, HIGH QUALITY 2 CYCLE OIL. (DO NOT USE
MULTI-VISCOSITY OILS). USE OF JIFFY® SPECIALLY
FORMULATED 2-CYCLE OIL IS RECOMMENDED.
CLEAN, FRESH,
REGULAR FUEL ONLY.
NOTE: DO NOT USE LEADED FUEL.
FUEL MUST BE FRESH AND CLEAN. NEVER USE FUEL
LEFT OVER FROM LAST SEASON OR STORED FOR
LONG PERIODS. DO NOT USE FUEL CONTAINING
METHANOL (WOOD
SUMMER BLEND FUEL.
NOTE: THE USE OF ALTERNATIVE FUELS SUCH AS E85 OR
E20 ARE NOT RECOMMENDED FOR USE IN JIFFY ICE
DRILLS. ALTERNATIVE FUELS WITH HIGH ALCOHOL
CONTENT CAN CAUSE HARD STARTING, POOR
PERFORMANCE, AND INTERNAL ENGINE DAMAGE.
NEVER MIX OR STORE GASOLINE/OIL MIXTURE
INDOORS OR IN ENCLOSED, POORLY VENTILATED
ENCLOSURES, WHERE FUEL FUMES MAY REACH AN
OPEN FLAME, SPARK OR PILOT LIGHT AS ON A
FURNACE, WATER HEATER, CLOTHES DRYER, ETC.
DAMAGE AND/OR PERFORMANCE PROBLEMS THAT
WILL OCCUR FROM USE OF FUELS, OTHER THAN
THOSE LISTED IN THE MANUAL WILL NOT BE
CONSIDERED WARRANTY.
WINTER BLEND, UNLEADED
ALCOHOL). DO NOT
TO MIX OIL AND GASOLINE
1. Mix a FRESH WINTER BLEND gasoline and JIFFY® two-cycle engine
oil in an approved, clean, safety-type container. Inferior quality gasoline
or oil may damage the engine, sealing rings, fuel lines or fuel tank.
2. Add recommended oil to gasoline per FUEL MIX CHART. DO NOT
MIX DIRECTLY IN ENGINE FUEL TANK. Pour oil into container first
then add gasoline.
3. Securely screw cap on container and shake vigorously. Once mixed, oil
and gasoline should not separate.
FUEL MIX CHART
Gas Oil To Be Added
1 Gal.

FUELING

1. Gasoline vapor pressure may build up inside gas tank of a two cycle
engine depending on weather conditions, venting system of the tank,
and the fuel used. To reduce the risk of injury from escaping gas fumes
and vapor, remove the gas cap on your drill slowly to release pressure
build-up.
2. Fill fuel tank with fuel mixture specified in the preceding "Oil and Fuel
Recommendations".
+ NEVER FILL FUEL TANK INDOORS, WHILE ENGINE IS RUNNING,
OR WHILE ENGINE IS HOT.
+ NEVER FILL FUEL TANK COMPLETELY. FILL TANK TO ½ INCH
BELOW BOTTOM OF FILLER NECK TO PROVIDE SPACE FOR
FUEL EXPANSION. WIPE ANY FUEL SPILLAGE FROM ENGINE
AND EQUIPMENT BEFORE STARTING ENGINE.
CHECK THE FOLLOWING BEFORE STARTING YOUR DRILL
1. Be sure spark plug wire is ATTACHED to spark plug.
2. Be sure ignition switch is in the ON Position.
3. Inspect the machine for proper condition and operation, paying special
USE
attention to the throttle control assembly, on/off switch, and drilling
assembly.
+ TO REDUCE THE RISK OF INJURY FROM THE TURNING DRILL
ASSEMBLY OR FROM REACTIVE FORCES, THE THROTTLE
ASSEMBLY AND RELATED MECHANISM MUST MOVE FREELY
AND RETURN IMMEDIATELY TO THE IDLE POSITION WHEN
RELEASED.
+ NEVER OPERATE YOUR DRILL IF IT HAS BEEN DAMAGED,
IMPROPERLY
SECURELY ASSEMBLED.
+ NEVER RUN ENGINE INDOORS OR IN ENCLOSED, POORLY
VENTILATED AREAS. ENGINE EXHAUST CONTAINS CARBON
MONOXIDE, AN ODORLESS AND DEADLY GAS.
+ TO REDUCE THE RISK OF INJURY FROM REACTIVE FORCES,
THE OPERATOR MUST HAVE A FIRM GRIP ON THE MACHINE
AND A GOOD FOOTHOLD BEFORE STARTING THE DRILL AND
OPENING THE THROTTLE.
+ KEEP HANDS, FEET, HAIR AND LOOSE CLOTHING AWAY
FROM ANY MOVING PARTS ON ENGINE AND EQUIPMENT.
+ WARNING – TEMPERATURE OF MUFFLER AND NEARBY
AREAS MAY EXCEED 150° F (65° C) AVOID THESE AREAS TO
AVOID BURNS OR OTHER INJURY.
-3-
MIXTURE 40:1
U.S.
Petrol Oil To Be Added
3.2 oz. 4 Liters
ADJUSTED OR
METRIC
100 ml
NOT COMPLETELY AND