Before First Use; Operation Of The Appliance - Inventum KI120T Mode D'emploi

3

before first use

Before you use the appliance for the first time, please do as follows: Carefully unpack the appliance and remove all the packaging
material. Keep the material (plastic bags and cardboard) out of reach of children. Check the appliance after unpacking for any
damage, possible from transportation. Remove any protective film that may still be on the ceramic plate. Clean the ceramic plate
with a damp cloth. Check that the voltage in your home corresponds with the voltage printed on the bottom of the appliance and plug
it in a socket.
4

operation of the appliance

Use only suitable cookware on the induction cooker. The cookware must have a diameter from 15 to 20 cm.
The controls of the cooker respond to touch, so you don't need to apply any pressure. Use the ball of your finger, not its tip.
A beep will sound each time a touch is registered.
Make sure the controls are always clean, dry, and that there is no object (e.g. a utensil or a cloth) covering them. Even a thin film of
water may make the controls difficult to operate.
PUT THE POT ON THE CERAMIC PLATE
• Make sure the air vents are not blocked and keep utensils away from the immediate surrounds of the ceramic plate.
• Make sure the cookware which has food or liquid is placed in the center of ceramic plate.
PLUG IN THE APPLIANCE
• After the power supply is connected, a beep will be heard. The display shows "L", indicating that the induction cooker is in standby
mode. As long as the induction cooker is in the standby mode, "L" will keep blinking.
TURN THE APPLIANCE ON
• After pressing the [ ON/STANDBY ] key, the induction cooker is ready for heating. Press the [ Function ] key, the induction
cooker enters heating mode.
• When the function key is not pressed in 10 seconds, after pressing the [ ON/STANDBY ] key, the induction cooker will switch
off automatically.
• After pressing the function key, if there is no proper pot on the ceramic plate, the induction cooker will not heat up and the
alarm will sound to indicate that a pot is required. One minute later, it will switch off automatically.
SETTING THE TEMPERATURE / POWER
• After switching on the induction cooker, press the [ Function ] key to enter the temperature or power level mode.
• Adjust the power level by pressing the increase setting key + or the decrease setting key - (range from 200 to 2000 watts).
• Adjust the temperature by pressing the increase setting key + or the decrease setting key - (range from 60° to 200°C).
SETTING THE TIMER
• Press the [ Timer ] key to enter the timer mode. When the timer indicator lights up and the numbers blink on the display, press the
[ + ] or [ - ] key to adjust the time duration. The timer can be set from 1 minute to 3 hours.
• When the adjustment is finished, the number on the display will be shown after blinking for several seconds. The induction cooker
starts counting down.
• When the counting down is over, the induction cooker automatically stops heating and switches off.
• The induction cooker will shut down when the default timer is reached unless the user sets the timer himself.
KEEP WARM FUNCTION
• Press the [ Keep warm ] key to maintain warmth. Using this mode, the induction cooker heats the ingredients with gentle power to
maintain a certain temperature inside the pot.
Note: Using this mode, the power level/ temperature cannot be adjusted.
LOCKING THE KEYS
The key lock function is for blocking and setting the hob in a save mode during use. Setting a higher heat setting or other alterations are
not possible. It is only possible to switch the appliance off.
• Press the [ + ] and [ - ] key simultaneously to start lock function. The lock indicator lights up. Now only the [ ON/STANDBY ] key can
be used to switch off the induction cooker, all the other operations are forbidden.
• Press the [ + ] and [ - ] key again simultaneously for 3 seconds to de-activate the lock function. The lock indicator turns off.
TURN THE APPLIANCE OFF
• When the operating time is over, the induction cooker switches off automatically.
• Press the [ ON/STANDBY ] key to turn off the appliance.
Note: Do not touch the surface of the ceramic while "H" is displayed, it means the ceramic plate is still too hot to touch. As soon as
the temperature has decreased enough the "H" indication will disappear. While "L" is displayed, it means the temperature low.
16
• English
[ ]
+