Publicité
Les langues disponibles
Les langues disponibles
EN
User Manual
Set of 3 lamp sockets E27 with radio remote control
1
Safety Instructions
1.1
General
•
Read the user manual completely and carefully before use.
The user manual is part of the product and contains important
information for correct use.
•
Keep this user manual.
The user manual must be available for uncertainties and passing the
product.
Risk of electric shock
•
Do not open the housing.
•
Do not modify product and accessories.
•
Do not short connectors and circuits.
•
Use product, product parts and accessories only in perfect
condition.
A defective device may not be put into operation, but must be discon-
nected from mains and protected against further use.
•
In case of questions, defects, mechanical damage, trouble and
other problems, non-recoverable by the documentation, contact
your dealer or producer.
Target group information
Not meant for children.
•
Secure packaging, small parts and insulation against acciden tal
use.
•
Avoid stresses such as heat and cold, moisture and direct sunlight
vibration and mechanical pressure.
•
Do not immerse the product in liquids and protect it from splashing
water.
1.2 Warning levels
Warnings against hazards that may result in injuries in case of
nonobservance.
Warnings against hazards that may result in material damage
in case of non-observance.
2
Description and Function
2.1
Product
The lamp sockets allow you to switch on and off up to 3 lamps, independently of
each other or parallel to each other, conveniently via radio remote control. Ideal for
storerooms, attics, cellars, garages, hallways and stairwells . Works through doors,
glass, thin walls and furniture.
2.2
Scope of delivery
Set of 3 lamp sockets E27, radio remote control, User manual
2.3
Operating elements and product parts
Fig. 2: Operating elements
1 Lamp socket E27
3 Radio remote control
5 Selection and ON push button 1 - 3
6 OFF push button 1 - 3
2.4
Specifications
Article number
Lamp socket
Operating voltage
Transmission frequency
Max. power per lamp socket:
Bulb
LED / Energy-saving lamp
Operating temperature range
socket design
socket material
Protection class / Protection level
Dimensions (L x Ø)
Weight per lamp socket
Radio remote control
Max. range of radio remote control
Dimensions (l x Ø)
Weight
REV2018-03-21
V1.0
2 Control LED
4 LED display
55499
220-240 @ 50 Hz
V~
433.92
MHz
60
W
20
W
0 ~ 35
°C
E27
ABS, Cooper, PBT
II / IP20
103.2 x 54.0
mm
73.0
g
30
m
81 x 36 x15
mm
26
g
Required battery for radio remote control (not included)
Type
Voltage
Number
Tab. 2: Specifications
3
Intended Use
We do not permit using the device in other ways like described in chapter
Description and Function. Use the product only in dry interior rooms. Not
attending to these regulations and safety instructions might cause fatal
accidents, injuries, and damages to persons and property.
4
Remote Control
Battery hazards
The battery of the radio remote control is replaceable.
•
Leave leaked, deformed or corroded batteries inside the product
and dispose it by appropriate protectives.
4.1
Activate remote control
1.
Open the battery compartment on the back of the radio remote
control in the direction of the arrow.
2.
Insert a suitable battery, see also chapter 2.4 "Technical data",
observing the polarity of plus and minus in the battery compart
ment.
3.
Close the battery compartment by pushing it, in opposite direction
to the arrow, on the remote control.
The remote control is now ready for use.
4.2
Change battery
1.
Replace the empty battery as needed with a new one of the same
type.
2.
Dispose of the empty battery in a professional
5
Connecting
Material demage
•
Do not overload the socket with lamps that are too strong!.
See also chapter 2.4 "Specifications"
The wireless lamp socket is designed for a maximum switching capaci-
ty of 60W.
1.
Compare the specifications of all used devices to ensure compati-
bility
2.
Check the scope of delivery for completeness and integrity.
3.
Turn off the lamp you want to equip with the lamp socket.
4.
Screw the lamp socket directly into the socket of the lamp.
5.
Screw the desired light source into the lamp socket.
6
Switch on/off
The lampholders are pre-set and can be used immediately.
1.
Turn on the lights.
The control LED (2) on the lamp socket starts to flash briefly. If the
control LED is lit steadily, the lamp socket is ready for use.
2.
Briefly press the lamp selection and ON button "ON 1" (5) on the
remote control to switch on the light.
If several lamp sockets are used, the next ON button "ON 2" or "ON 3"
must be pressed to switch on the respective lighting.
3.
Switch off the light when it is no longer required via the OFF switch
(OFF) 1,2 or 3, depending on the assignment
4.
Turn off the newly programmed lamp and repeat steps 1 - 3 for
additional lamps.
7
Programming
With the wireless remote control, you can program up to 3 lamp
sockets at the same time or independently of each other and switch
your lighting on and off. For reprogramming, proceed as follows:
7.1
Redistribution for single switching
1.
Point the radio remote control (3) to the one to be programmed
lamp socket.
2.
Only switch on the lighting with the lamp socket to be programmed.
The control LED (2) on the lamp socket starts to flash for approx. 5
seconds.
3.
Press and hold the desired lamp selector button (5) on the radio re
mote control for approx. 3 seconds while the control LED on the
lamp socket flashes.
Programming was successful when the control LED on the lamp
socket stops flashing and the selected illumination is on.
7.2
Simultaneous multiple switching
1.
Switch on all the lights that are equipped with additional lamp
sockets and that are to be operated in parallel.
The LED indicators (2) on the lamp sockets start to flash for about 5
seconds.
Press and hold the desired lamp selector button (5) on the remote
2.
control for about 3 seconds while the LED indicators on the lamp
sockets are flashing.
Programming was successful when the control LEDs on the lamp
sockets stop flashing and turn on the selected lights.
- 3 -
55499
Alkaline battery 23A
12 V
1x
way.
Goobay
by Wentronic GmbH | Pillmannstraße 12
38112 Braunschweig | Germany
®
Publicité
