Télécharger Imprimer la page
Broan LOSONE SELECT L100L Manuel D'instructions
Broan LOSONE SELECT L100L Manuel D'instructions

Broan LOSONE SELECT L100L Manuel D'instructions

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

LOSONE SELECT
VENTILATORS
In-Line • 120V
READ AND SAVE THESE INSTRUCTIONS
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY
TO PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer. If
you have questions, contact the manufacturer at the address or
telephone number listed in the warranty.
2. Before servicing or cleaning unit, switch power off at service panel
and lock the service disconnecting means to prevent power from
being switched on accidentally. When the service disconnecting
means cannot be locked, securely fasten a prominent warning
device, such as a tag, to the service panel.
3. Installation work and electrical wiring must be done by a qualified
person(s) in accordance with all applicable codes and standards,
including fire-rated construction codes and standards.
4. Sufficient air is needed for proper combustion and exhausting of
gases through the flue (chimney) of fuel burning equipment to
prevent backdrafting. Follow the heating equipment
manufacturer's guideline and safety standards such as those
published by the National Fire Protection Association (NFPA),
and the American Society for Heating, Refrigeration and Air Con-
ditioning Engineers (ASHRAE), and the local code authorities.
5. When cutting or drilling into wall or ceiling, do not damage elec-
trical wiring and other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
7. To reduce the risk of fire, use only metal ductwork.
8. If this unit is to be installed over a tub or shower, it must be marked
as appropriate for the application and be connected to a GFCI
(Ground Fault Interrupter) - protected branch circuit.
9. Never place a switch where it can be reached from a tub or
shower.
10. This unit must be grounded.
TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
1. Never leave surface units unattended at high settings. Boilovers
cause smoking and greasy spillovers that may ignite. Heat oils
slowly on low or medium settings.
2. Always turn hood ON when cooking at high heat or when cooking
flaming foods.
3. Clean ventilating fans frequently. Grease should not be allowed
to accumulate on fan or filter.
4. Use proper pan size. Always use cookware appropriate for the
size of the surface element.
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT
OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING:*
1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal
tray, then turn off the burner. BE CAREFUL TO PREVENT
BURNS. If the flames do not go out immediately, EVACUATE
AND CALL THE FIRE DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN — You may be burned.
3. DO NOT USE WATER, including wet dishcloths or towels - violent
steam explosion will result.
4. Use an extinguisher ONLY if:
A. You know you have a Class ABC extinguisher and you al-
ready know how to operate it.
B. The fire is small and contained in the area where it started.
C. The fire department is being called.
D. You can fight the fire with your back to an exit.
* Based on "Kitchen Fire Safety Tips" published by NFPA.
®
®
L100L • L150L • L200L • L250L • L300L
CAUTION
1. For general ventilating use only. Do not use to exhaust hazard-
ous or explosive materials and vapors.
2. To avoid motor bearing damage and noisy and/or unbalanced
impellers, keep drywall spray, construction dust, etc. off power
unit.
3. If ventilator is installed in an unconditioned space (such as
an attic): Surround the ventilator with thermal insulation - to
minimize possible condensation.
4. Please read specification label on product for further informa-
tion and requirements.
TABLE OF CONTENTS
This manual is divided into sections as follows:
• "TYPICAL INSTALLATION"
This section shows a common installation in new and existing,
frame construction.
- Mounting (new construction)
- Mounting (existing construction)
- Wiring
- Ducting (straight through blower discharge)
• "MOUNTING OPTIONS"
• "WIRING OPTIONS"
- Wiring Plate Position
• "DUCTING OPTIONS"
- Blower Discharge Positions
- Ducting (right angle blower discharge)
• "USE AND CARE"
• "SERVICE PARTS"
• "WARRANTY"
Installer: Leave this manual with
the homeowner.
Homeowner: Use and Care
information on page 3.
MODELS
Page 1
99042723G

Publicité

loading

Sommaire des Matières pour Broan LOSONE SELECT L100L

  • Page 1 MODELS L100L • L150L • L200L • L250L • L300L ® Page 1 LOSONE SELECT ® VENTILATORS In-Line • 120V READ AND SAVE THESE INSTRUCTIONS WARNING CAUTION TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY 1. For general ventilating use only. Do not use to exhaust hazard- TO PERSONS, OBSERVE THE FOLLOWING: ous or explosive materials and vapors.
  • Page 2 MODELS L100L • L150L • L200L • L250L • L300L ® Page 2 TYPICAL INSTALLATION TYPICAL INSTALLATION MOUNTING (New Frame Construction) WIRING BLACK Mounting brackets factory- ROUND DUCT* shipped in position for ½” BLACK TOP / BACK (12.7 mm) ceiling material. OF HOUSING GROUND TO ADDITIONAL...
  • Page 3 MODELS L100L • L150L • L200L • L250L • L300L ® Page 3 MOUNTING OPTIONS DUCTING OPTIONS BLOWER DISCHARGE POSITIONS ¼-20 hex nuts secure mounting brackets to housing. Loosen and re-tighten or remove and replace nuts as necessary for desired mounting bracket position.
  • Page 4 THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. During this one-year period, Broan-NuTone Canada will, at its option, repair or replace, without charge, any product or part which is found to be defective under normal use and service.
  • Page 5 MODÈLES MODELS L100L • L150L • L200L • L250L • L300L ® Page 5 VENTILATEURS LOSONE SELECT ® Montage dans ligne • 120 V LIRE ET CONSERVER CES INSTRUCTIONS AVERTISSEMENT AVERTISSEMENT 4 . U t i l i s e z u n e x t i n c t e u r S E U L E M E N T s i : POUR RÉDUIRE LE RISQUE D´INCENDIE, DE CHOC ÉLECTRIQUE OU DE A .
  • Page 6 MODÈLES MODELS L100L • L150L • L200L • L250L • L300L ® Page 6 INSTALLATION TYPIQUE INSTALLATION TYPIQUE MONTAGE (Construction en cours) CÂBLAGE CONDUIT CIRCULAIRE* Supports préassemblés NOIR AU DESSUS / pour plafonds de ½ po NOIR ARRIÈRE DU (12.7 mm) d’épaisseur. BOÎTIER FIL DE TERRE À...
  • Page 7 MODÈLES MODELS L100L • L150L • L200L • L250L • L300L ® Page 7 OPTIONS DE MONTAGE OPTIONS D’INSTALLATION DES CONDUITS Des écrous à six pans ¼-20 fixent les supports au boîtier. Desserrer POSITIONS DE LA DÉCHARGE DE LA SOUFFLERIE et resserrer ou retirer et replacer les écrous si nécessaire, selon la position désirée pour le support.
  • Page 8 Pour le service sous garantie, vous devez (a) aviser Broan-NuTone Canada á l’adresse ou au numéro de téléphone ci-dessous, (b) donner le numéro du modèle et l’identification de la pièce et (c) décrire la nature de tout défaut dans le produit ou la pièce. Au temps de demander le service sous garantie, vous devez présenter une preuve de la date d’achat original.

Ce manuel est également adapté pour:

Losone select l150lLosone select l200lLosone select l250lLosone select l300l