Switching The Appliance On / Off; Start-Up; Suction Pipe; Floor Nozzle With Turbo Brush - Profi Care PC-BS 3036 A Mode D'emploi

cleaner. Especially on shag-pile carpet, the cleaning
performance is not sufficient owing to its design.
• Contaminated filters reduce the suction power of the vac-
uum cleaner. Therefore, we recommend regular cleaning
of the existing dirt filters.
• Ideally, clean the filters whenever they have been subject
to a prolonged use.
• Please regularly check and clean the electric floor
nozzle.
• If necessary, clean heavily soiled floors multiple times
and / or use a conventional 230 V~ floor vacuum cleaner.

Switching the Appliance On / Off

• The button
turns the appliance on and off.
• Press the ECO button to toggle between low and high
power level. In ECO mode, you can extend the life cycle
of the rechargeable battery. The LED between the two
buttons will light up.

Start-Up

Suction Pipe

• Insert the suction pipe with the two contact pins into
the connection on the hand appliance. It must audibly
engage.
• To disconnect the suction pipe, press the release (10)
and pull out the pipe at the same time.
• Use the bracket to attach the upholstery / brush nozzle
and the crevice nozzle to the suction tube. This way, you
always have the accessories at hand.

Floor Nozzle with Turbo Brush

• The floor nozzle is suitable for all floor coverings except
for shag-pile carpets.
• During operation, the LEDs on the floor nozzle light up
for better visibility in dark areas.
CAUTION:
You cannot replace the LEDs.
• Stick the lower end of the suction pipe onto the connec-
tor on the floor nozzle. Note the contact pins on the floor
nozzle. The suction pipe must audibly s snap into place.
• To disconnect the suction pipe, press the release (12)
and pull out the pipe at the same time.

Nozzle Attachments

There are two different ways for connecting these nozzles
to the appliance:
Connection at the Hand Unit
• Note the guide lug on the crevice nozzle and on the
upholstery / brush nozzle. Hold the nozzles in such a way
that the guide lug points upwards.
• Plug one of the nozzles into the port on the handset. It
must engage audibly.
50
PC-BS3036A_IM_new (ab PO60756)
• To release the respective nozzle, press the release
button (10) while pulling it out at the same time.
• The special brush has neither a guide lug nor a release
button. You can simply attach this brush and remove it
again.
Connection to the Suction Pipe
At the lower end of the suction pipe, you will find the same
plug connection as on the handset. Mount / dismount the
nozzle as described above.
Crevice Nozzle
For vacuuming dirt from corners, joints and small gaps.
Combined Upholstery / Brush Nozzle
This nozzle is suitable for removing dust from smaller
surfaces such as upholstery, furniture or curtains. Use
the nozzle with locked brush to prevent scratching of the
surface to be cleaned.
• For this, press the button and push the brush to the end
of the nozzle. It must engage.
• Press the button again to unlock the brush.
Special Brush
This nozzle is especially good for gentle cleaning of larger
susceptible surfaces.

Assembly the Wall Holder

WARNING:
Make sure beforehand whether there are cables in the
wall which could be damaged!
CAUTION:
Place the wall holder so that the appliance is not exposed
to direct sunlight or other heat sources.
NOTE:
If you would like to simultaneously use the wall mount as
a charging station, there must be a power outlet nearby.
1. Measure the height for the wall holder. Hold the vacuum
cleaner against the wall with the suction pipe and the
floor nozzle installed.
2. Hold the wall bracket against the wall. Mark 2 drill holes.
3. Drill the holes and insert the wall plugs into the wall.
4. Insert the screws through the holes of the wall holder.
5. Tighten the screws with a screwdriver hand-tight.

Charging the Rechargeable Battery

CAUTION:
Do not charge the rechargeable battery unsupervised.
1. Turn off the appliance.
2. Connect the power adapter with the connection
socket (5).
07.05.21